Craftsman 54930 Manual De Usuario
Planning
Identify the type and height of your garage door. Survey your
garage area to see if any of the conditions below apply to your
installation. Additional materials may be required. You may find it
helpful to refer back to this page and the accompanying
illustrations as you proceed with the installation of your opener.
Depending on your requirements, there are several installation
steps which may call for materials or hardware not included in the
carton.
garage area to see if any of the conditions below apply to your
installation. Additional materials may be required. You may find it
helpful to refer back to this page and the accompanying
illustrations as you proceed with the installation of your opener.
Depending on your requirements, there are several installation
steps which may call for materials or hardware not included in the
carton.
l
Installation Step 1 – Look at the wall or ceiling above the
garage door. The header bracket must be securely fastened to
structural supports.
garage door. The header bracket must be securely fastened to
structural supports.
l
Installation Step 5 – Do you have a finished ceiling in your
garage? If so, a support bracket and additional fastening
hardware may be required.
garage? If so, a support bracket and additional fastening
hardware may be required.
l
Installation Step 12 – Depending upon garage construction,
extension brackets or wood blocks may be needed to install
sensors.
extension brackets or wood blocks may be needed to install
sensors.
l
Installation Step 12 – Alternate floor mounting of the safety
reversing sensor will require hardware not provided.
reversing sensor will require hardware not provided.
l
Do you have an access door in addition to the garage door? If
not, Model 139.53702 Emergency Key Release is required. See
Accessories page.
not, Model 139.53702 Emergency Key Release is required. See
Accessories page.
l
Look at the garage door where it meets the floor. Any gap
between the floor and the bottom of the door must not exceed
1/4" (6 mm). Otherwise, the safety reversal system may not
work properly. See Adjustment Step 2. Floor or door should be
repaired.
between the floor and the bottom of the door must not exceed
1/4" (6 mm). Otherwise, the safety reversal system may not
work properly. See Adjustment Step 2. Floor or door should be
repaired.
SECTIONAL DOOR INSTALLATION
l
Do you have a steel, aluminum, fiberglass or glass panel
door? If so, horizontal and vertical reinforcement is required
(Installation Step 8).
door? If so, horizontal and vertical reinforcement is required
(Installation Step 8).
l
The opener should be installed above the center of the door. If
there is a torsion spring or center bearing plate in the way of
the header bracket, it may be installed within 4 feet (1.22 m) to
the left or right of the door center. See Installation Steps 1
and 8.
there is a torsion spring or center bearing plate in the way of
the header bracket, it may be installed within 4 feet (1.22 m) to
the left or right of the door center. See Installation Steps 1
and 8.
l
If your door is more than 7 feet (2.13 m) high, see rail
extension kits listed on Accessories page.
extension kits listed on Accessories page.
Safety Reversing Sensor
Header Wall
Access Door
Safety Reversing
Sensor
Sensor
Gap between floor
and bottom of door
must not exceed 1/4" (6 mm).
and bottom of door
must not exceed 1/4" (6 mm).
Extension Spring
Horizontal and vertical reinforcement
is needed for lightweight garage doors
(fiberglass, steel, aluminum, door with
glass panels, etc.). See page 18 for details.
is needed for lightweight garage doors
(fiberglass, steel, aluminum, door with
glass panels, etc.). See page 18 for details.
Support bracket &
fastening hardware
is required.
See page 16.
fastening hardware
is required.
See page 16.
FINISHED CEILING
Motor unit
Wall-mounted
Door Control
OR
Torsion Spring
Slack in chain tension
is normal when garage
door is closed.
is normal when garage
door is closed.
Vertical
Centerline
of Garage
Door
Centerline
of Garage
Door
Emergency
Release Rope
& Handle
Release Rope
& Handle
Straight
Door
Arm
Door
Arm
Garage
Door
Spring
Door
Spring
Door
Bracket
Bracket
Header
Bracket
Bracket
Garage
Door
Door
Header
Wall
Wall
CLOSED POSITION
Rail Tab
Curved
Door Arm
Door Arm
Chain
Trolley
SECTIONAL DOOR IINSTALLATION
4