Craftsman 38907 Manual De Usuario
8
Operation (continued)
Vacuuming Liquids
!
!
1. Verify that the power cord is
disconnected from the outlet. (Fig. 1)
2. Remove cartridge fi lter as shown in
Removing and Cleaning Cartridge
Filter on page 10. Then install the
foam sleeve fi lter as shown in
Installing Foam Sleeve Filter on page
12 and secure power head back on
the collection tank.
disconnected from the outlet. (Fig. 1)
2. Remove cartridge fi lter as shown in
Removing and Cleaning Cartridge
Filter on page 10. Then install the
foam sleeve fi lter as shown in
Installing Foam Sleeve Filter on page
12 and secure power head back on
the collection tank.
DO NOT USE THE CARTRIDGE FILTER
FOR LIQUID VACUUMING.
FOR LIQUID VACUUMING.
3. Fit the desired nozzle to the vacuum
hose. (Fig. 2)
4. Verify that the power switch is in the ‘O’
OFF position before plugging the
power cord into the outlet. (Fig. 3)
5. Turn the motor on by pressing the
switch to the ‘I’ ON position. (Fig. 4)
6. Once you have completed vacuuming,
press the power switch to the 'O' (OFF)
position and unplug the power cord
from the outlet.
7. After use, empty the collection tank by
unscrewing the drain cap and drain
liquids into suitable receptacle or
drain. (Fig. 5) Remember to refi t the
drain cap to the tank after draining.
hose. (Fig. 2)
4. Verify that the power switch is in the ‘O’
OFF position before plugging the
power cord into the outlet. (Fig. 3)
5. Turn the motor on by pressing the
switch to the ‘I’ ON position. (Fig. 4)
6. Once you have completed vacuuming,
press the power switch to the 'O' (OFF)
position and unplug the power cord
from the outlet.
7. After use, empty the collection tank by
unscrewing the drain cap and drain
liquids into suitable receptacle or
drain. (Fig. 5) Remember to refi t the
drain cap to the tank after draining.
IMPORTANT! When vacuuming large
quantities of liquids, do not immerse the
nozzle completely in the liquid; leave a
gap at the tip of the nozzle opening to
allow air infl ow. The machine is fi tted with
a fl oat valve that stops the suction action
when the collection tank reaches its
maximum capacity. You will notice an
increase in motor speed. When this
happens, turn off the machine,
disconnect from power supply, and drain
the liquid into a suitable receptacle or
drain. To continue vacuuming, refi t the
collection tank with the drain cap. After
wet vacuuming, turn the machine off and
remove plug from power supply. Empty
the collection tank, clean and dry the
inside and outside before storage.
quantities of liquids, do not immerse the
nozzle completely in the liquid; leave a
gap at the tip of the nozzle opening to
allow air infl ow. The machine is fi tted with
a fl oat valve that stops the suction action
when the collection tank reaches its
maximum capacity. You will notice an
increase in motor speed. When this
happens, turn off the machine,
disconnect from power supply, and drain
the liquid into a suitable receptacle or
drain. To continue vacuuming, refi t the
collection tank with the drain cap. After
wet vacuuming, turn the machine off and
remove plug from power supply. Empty
the collection tank, clean and dry the
inside and outside before storage.
REMEMBER! The foam filter must be
removed after wet vacuuming and a
cartridge filter must be installed before
dry vacuuming again.
removed after wet vacuuming and a
cartridge filter must be installed before
dry vacuuming again.
2
4
5
1
3
WARNING: Be sure to read, understand and apply all the information in the
Important Safety Instructions section at the beginning of this operator's manual.
Do not vacuum in areas with fl ammable gases, vapors, or explosive dusts in the
air. Flammable gases or vapors include but are not limited to: lighter fl uid,
solvent type cleaners, oil-base paints, gasoline, alcohol or aerosol sprays.
Explosive dusts include but are not limited to: coal, magnesium, grain or gun
powder. To reduce the risk of health hazards from vapors or dust, do not
vacuum toxic materials.
WARNING: Do not plug in power cord to power outlet, make sure plug is
disconnected before assembling the Wet/Dry Vac.
Important Safety Instructions section at the beginning of this operator's manual.
Do not vacuum in areas with fl ammable gases, vapors, or explosive dusts in the
air. Flammable gases or vapors include but are not limited to: lighter fl uid,
solvent type cleaners, oil-base paints, gasoline, alcohol or aerosol sprays.
Explosive dusts include but are not limited to: coal, magnesium, grain or gun
powder. To reduce the risk of health hazards from vapors or dust, do not
vacuum toxic materials.
WARNING: Do not plug in power cord to power outlet, make sure plug is
disconnected before assembling the Wet/Dry Vac.