Timberk SWH SE1 30 VU Manual De Usuario
3
www.timberk.com electric storage water heater
5. It is forbidden to switch on the water heater if it is not filled with water or
if water cannot go through the pressure safety valve.
6. Never use the water heater if it is damaged.
7. Do not remove the water heater cover when it is in operation.
8. Immediately unplug the water heater from the electrical main if strange
sounds, odour or smoke comes out from it.
9.Always unplug the water heater from the electrical main during
thunderstorm.
10. Prior to cleaning and maintenance of the water heater unplug it from
the electrical main every time. Cleaning and maintenance must be
performed in compliance with the instructions contained in this manual.
11. Do not use hazardous chemical substances to clean the water heater
and prevent their contact with the appliance.
12. To prevent electrical shock the damaged power cord must be replaced
only by qualified specialists in manufacturer's authorized service centres.
13. To prevent electrical shock do not place the power cord nearby heating
devices and flammable or combustible agents.
14. As temperature of water in the water heater can reach 75°C when it is in
operation you should not place your body parts under hot water upon the
first run. To prevent burns you should adjust the temperature of the
outflowing water.
15. Do not use the water heater for purposes not stipulated in this
instruction manual.
16. Do not use the water heater in an explosive or corrosive environment.
Do not store petrol and any other volatile flammable liquids near to the
appliance. It is very dangerous!
17. It is forbidden to make alterations in the design of the water heater or
modify it.
18. Any service works must be performed by a specialized organisation
and qualified specialists. Improper installation may cause voiding of
guarantee maintenance.
19. The water heater is not intended for use by children and persons with
reduced physical, sensory or mental capabilities, or a lack of experience
and knowledge unless they are under supervision or instructed on using
of the appliance by a person responsible for their safety. Children should
be controlled to ensure that they do not play with the appliance.
if water cannot go through the pressure safety valve.
6. Never use the water heater if it is damaged.
7. Do not remove the water heater cover when it is in operation.
8. Immediately unplug the water heater from the electrical main if strange
sounds, odour or smoke comes out from it.
9.Always unplug the water heater from the electrical main during
thunderstorm.
10. Prior to cleaning and maintenance of the water heater unplug it from
the electrical main every time. Cleaning and maintenance must be
performed in compliance with the instructions contained in this manual.
11. Do not use hazardous chemical substances to clean the water heater
and prevent their contact with the appliance.
12. To prevent electrical shock the damaged power cord must be replaced
only by qualified specialists in manufacturer's authorized service centres.
13. To prevent electrical shock do not place the power cord nearby heating
devices and flammable or combustible agents.
14. As temperature of water in the water heater can reach 75°C when it is in
operation you should not place your body parts under hot water upon the
first run. To prevent burns you should adjust the temperature of the
outflowing water.
15. Do not use the water heater for purposes not stipulated in this
instruction manual.
16. Do not use the water heater in an explosive or corrosive environment.
Do not store petrol and any other volatile flammable liquids near to the
appliance. It is very dangerous!
17. It is forbidden to make alterations in the design of the water heater or
modify it.
18. Any service works must be performed by a specialized organisation
and qualified specialists. Improper installation may cause voiding of
guarantee maintenance.
19. The water heater is not intended for use by children and persons with
reduced physical, sensory or mental capabilities, or a lack of experience
and knowledge unless they are under supervision or instructed on using
of the appliance by a person responsible for their safety. Children should
be controlled to ensure that they do not play with the appliance.
3. PERFORMANCE CHARACTERISTICS
Main distinctive features
1.Completely automatic control: automatic water heating, continuous
automatic water temperature control.
2.Protection system:
Drop Defense leakage protection and protection against excessive
pressure inside the tank (pressure safety valve);
HOT Defense two-level overheating protection (temperature detec-
tor and temperature limiter).
3.Steel inner tank with special protection coat from titanium finely-
divided glass enamel drown down by the modern method of electrostatic
dry enamelling is resistant to corrosion and boiler scale. Additionally,
enamel possesses increased adhesive capacity and high flexibility (heat-
treated at the temperature of 850° ) that allow it to expand and shrink
upon temperature differentials in the same proportion as the walls of the
inner tank not forming micro-cracks in which corrosion pits can appear.
4.Pipes of heating elements are designed taking into account high
heating load: safe and reliable with increased service life.
5.The water heater is fitted with an anode rod for protection against
corrosion of the inner tank and decrease of boiler scale on the heating
element.
6.Inner urethane foam insulation of increased thickness allows for
effective retain of temperature of heated water and minimizes heat losses
decreasing power consumption of the water heater.
The water heater has simple design and it is convenient in service.
automatic water temperature control.
2.Protection system:
Drop Defense leakage protection and protection against excessive
pressure inside the tank (pressure safety valve);
HOT Defense two-level overheating protection (temperature detec-
tor and temperature limiter).
3.Steel inner tank with special protection coat from titanium finely-
divided glass enamel drown down by the modern method of electrostatic
dry enamelling is resistant to corrosion and boiler scale. Additionally,
enamel possesses increased adhesive capacity and high flexibility (heat-
treated at the temperature of 850° ) that allow it to expand and shrink
upon temperature differentials in the same proportion as the walls of the
inner tank not forming micro-cracks in which corrosion pits can appear.
4.Pipes of heating elements are designed taking into account high
heating load: safe and reliable with increased service life.
5.The water heater is fitted with an anode rod for protection against
corrosion of the inner tank and decrease of boiler scale on the heating
element.
6.Inner urethane foam insulation of increased thickness allows for
effective retain of temperature of heated water and minimizes heat losses
decreasing power consumption of the water heater.
The water heater has simple design and it is convenient in service.
ENGLISH