Carrier 42 UQV 060 M/38 UYV 060 M Manual De Usuario

Descargar
Página de 8
Set your preferred operation for future use. The setting will be memorized by the 
unit for future operation (except airflow direction).
  1.  Select your preferred operation.
 2. 
 
Press and hold 
 for 3 seconds to memorize the setting. The P 
mark displays.
 3. 
Press 
 : Operate the preset operation.
To automatically restart the air conditioner after the power failure (Power of the 
unit must be on.)
Setting
1.  
 Press and hold the RESET button on the indoor unit for 3 seconds to set 
the operation. (3 beep sound and OPERATION lamp blink 5 time/sec for 5 
seconds)
2.  
Press and hold the RESET button on the indoor unit for 3 seconds to cancel 
the operation. (3 beep sound but OPERATION lamp does not blink)
•  In case of ON timer or OFF timer are set, AUTO RESTART 
OPERATION does not activate.
For ECO sleep automatically control air flow and automatically turn OFF.
 Press 
 : Select 1, 3, 5 or 9 hrs for OFF timer operation.
  Note:  The cooling operation, the set temperature will increase automatically 
1 degree/hour for 2 hours (maximum 2 degrees increase). For heating 
operation the set temperature will decrease.
To operate at super low fan speed for quiet operation (except in DRY mode)
 Press 
 : Start and stop the operation.
  Note:  Under certain conditions, QUIET operation may not provide adequate
cooling due to low sound features.
To separate using of remote control for each indoor unit in case of 2 air 
conditioners are installed nearly.
Remote Control B Setup.
1.  Press RESET button on the indoor unit to turn the air conditioner ON.
2.  Point the remote control at the indoor unit.
3.  Push and hold 
 button on the Remote Control by the tip of the pencil. 
“00” will be shown on the display.
4.  Press 
 during pushing 
. “B” will show on the display and “00” 
will disappear and the air conditioner will turn OFF. The Remote Control B 
is memorized.
Note: 1. Repeat above step to reset Remote Control to be A.
 
2. Remote Control A has not “A” display.
 
3. Default setting of Remote Control from factory is A.
The unit does not operate.
Cooling is abnormally low.
•   The power main switch is turned off. 
•   The circuit breaker is activated to cut 
off the power supply. 
•   Stoppage of electric current 
•   ON timer is set. 
•   The filters are blocked with dust.
•   The temperature has been set 
improperly.
•   The windows or doors are opened.
•   The air inlet or outlet of the outdoor 
unit is blocked.
•   The fan speed is too low.
•   The operation mode is FAN or DRY.
2
1
PRESET OPERATION
12
ECO SLEEP OPERATION
15
QUIET OPERATION
14
AUTO RESTART OPERATION
13
 Firstly, turn off the circuit breaker.
Filter Reset
FILTER lamp lights on; the filter must be cleaned.
To turn off the lamp, push the RESET button on the indoor unit or the FILTER 
button on the remote control.
Indoor Unit and Remote Control
•   Clean the indoor unit and the remote control with a wet cloth when needed. 
•   No benzine, thinner, polishing powder or chemically-treated duster.
MAINTENANCE
16
TROUBLESHOOTING (CHECK POINT)
18
REMOTE CONTROL A-B SELECTION
19
 1. 
 
 
Three-minute protection feature: To prevent the unit from being activated 
for 3 minutes when suddenly restarted or switched to ON.
 2. 
 
Preheating operation: Warm up the unit for 5 minutes before blowing warm 
air.
 3. 
 
Warm air control: When the room temperature reaches the set 
temperature, the fan speed is automatically reduced and the outdoor unit 
will stop.
 4. 
 
Automatic defrosting: Fans will stop during defrost operation.
 5. 
 
Heating capacity: Heat is absorbed from outdoor and released into 
the room. When the outdoor temperature is too low, use another 
recommended heating apparatus in combination with the air conditioner.
 6. 
 
Consideration for accumulated snow: Select the position for outdoor unit 
where it will not be subjected to snow drifts, accumulation of leaves or 
other seasonal debris.
 7. 
 
Some minor cracking sound may occur when unit operating. This is 
normal because the cracking sound may be caused by expansion/
contraction of plastic.
  Note: Item 2 to 6 for Heating model
Air conditioner operating conditions
Temp.
Operation
Outdoor Temperature
Room 
Temperature
42UQV035M,
 050M, 060M Series
42UQV025M
 Series
Heating
–15°C ~ 24°C
–10°C ~ 24°C
Less than 28°C
Cooling
–10°C ~ 46°C
15°C ~ 43°C
21°C ~ 32°C
Dry
–10°C ~ 46°C
15°C ~ 43°C
17°C ~ 32°C
OPERATION AND PERFORMANCE
17
Carrier1110655103(01_EN).indd   4
Carrier1110655103(01_EN).indd   4
2/6/13   3:19 PM
2/6/13   3:19 PM