Cisco Cisco ONS 15454 SONET Multiservice Provisioning Platform (MSPP) Notas de publicación
3
Release Notes for Cisco ONS 15454 Release 7.0.1
OL-9647-01
Caveats
Maintenance and Administration
Caution
VxWorks is intended for qualified Cisco personnel only. Customer use of VxWorks is not recommended,
nor is it supported by Cisco's Technical Assistance Center. Inappropriate use of VxWorks commands can
have a negative and service affecting impact on your network. Please consult the troubleshooting guide
for your release and platform for appropriate troubleshooting procedures. To exit without logging in,
enter a Control-D (hold down the Control and D keys at the same time) at the Username prompt. To exit
after logging in, type “logout” at the VxWorks shell prompt.
nor is it supported by Cisco's Technical Assistance Center. Inappropriate use of VxWorks commands can
have a negative and service affecting impact on your network. Please consult the troubleshooting guide
for your release and platform for appropriate troubleshooting procedures. To exit without logging in,
enter a Control-D (hold down the Control and D keys at the same time) at the Username prompt. To exit
after logging in, type “logout” at the VxWorks shell prompt.
CSCsd49163
In a Y cable protection group using TXP_MR_10E or TXT_MR_10DME cards the switch time when
you remove a trunk fibre is sometimes longer than 50 ms. This issue will be resolved in a future release.
you remove a trunk fibre is sometimes longer than 50 ms. This issue will be resolved in a future release.
CSCsd21294
If you disconnect a subtended shelf from a multi-shelf node controller, the Communication failure is not
correctly characterized by the LCD and Fan Tray LEDs of the multi-shelf node. You can use CTC or TL1
to get the status of the nodes correctly, however. This issue will be resolved in a future release.
correctly characterized by the LCD and Fan Tray LEDs of the multi-shelf node. You can use CTC or TL1
to get the status of the nodes correctly, however. This issue will be resolved in a future release.
CSCsd22880
The APC regulations when a channel is dropped from an AD4C are not correctly managed. Consider a
channel dropped from the first CHAN-TX port of an AD4C card. In the CTC > Maintenance > DWDM
tab the APC Last modification date is never changed; it remains N/A. In any case of span aging
conditions, the object is always incorrectly referred to the fourth channel of the add/drop card, even if
that channel is not active. This issue will be resolved in a future release.
channel dropped from the first CHAN-TX port of an AD4C card. In the CTC > Maintenance > DWDM
tab the APC Last modification date is never changed; it remains N/A. In any case of span aging
conditions, the object is always incorrectly referred to the fourth channel of the add/drop card, even if
that channel is not active. This issue will be resolved in a future release.
CSCsd32197
Four channel Mux/Demux PM counters on CHAN ports (both TX and RX) fail to update after midnight
in both CTM and TL1. This issue will be resolved in a future release.
in both CTM and TL1. This issue will be resolved in a future release.
CSCsd33369
ALS mode can be set to Auto Restart on a TXP_MR_10G trunk port via TL1 when the TXP_MR_10G
card is configured for an Ethernet 10G LAN payload. This issue will be resolved in a future release.
card is configured for an Ethernet 10G LAN payload. This issue will be resolved in a future release.
CSCed23484
A user might remain in the logged-in state after rebooting the PC while logged into a node running CTC.
The user login will time out once the “Idle User Timeout” limit is up. Alternatively, you can log in as a
superuser and force the user off. This issue will not be resolved.
The user login will time out once the “Idle User Timeout” limit is up. Alternatively, you can log in as a
superuser and force the user off. This issue will not be resolved.