Cisco Cisco Email Security Appliance C190 Guía Del Usuario
3-18
Cisco AsyncOS 8.5.6 for Email User Guide
Chapter 3 Setup and Installation
Using the System Setup Wizard
Each interface can be configured to accept mail (incoming), relay email (outgoing), or appliance
management. During setup, you are limited to one of each. Typically, you would use one interface for
incoming, one for outgoing, and one for appliance management. On the C160/170 appliances, you would
typically use one interface for both incoming and outgoing mail, and the other interface for management.
management. During setup, you are limited to one of each. Typically, you would use one interface for
incoming, one for outgoing, and one for appliance management. On the C160/170 appliances, you would
typically use one interface for both incoming and outgoing mail, and the other interface for management.
You must configure one interface to receive email.
Assign and configure a logical IP address to one of the physical Ethernet interfaces on the appliance. If
you decide to use both the Data 1 Ethernet port and the Data 2 Ethernet port, you need this information
for both connections.
you decide to use both the Data 1 Ethernet port and the Data 2 Ethernet port, you need this information
for both connections.
C660/670, C360/370, and X1060/1070 customers: Cisco recommends using one of the physical
Ethernet ports to connect directly to the Internet for the purposes of receiving inbound email through
public listeners, and using another physical Ethernet port to connect directly to your internal network for
the purposes of relaying outbound email through private listeners.
Ethernet ports to connect directly to the Internet for the purposes of receiving inbound email through
public listeners, and using another physical Ethernet port to connect directly to your internal network for
the purposes of relaying outbound email through private listeners.
C160/170 customers: Typically, the System Setup Wizard will configure only one physical Ethernet
port with one listener for both receiving inbound email and relaying outbound email.
port with one listener for both receiving inbound email and relaying outbound email.
See
.
The following information is required:
•
The IP address assigned by your network administrator. This can be an IPv4 address, an IPv6
address, or both.
address, or both.
•
For IPv4 addresses: the netmask of the interface. AsyncOS only accepts a netmask in CIDR format.
For example,
For example,
/24
for the
255.255.255.0
subnet.
For IPv6 addresses: the prefix in CIDR format. For example
/64
for a 64-bit prefix.
•
(optional) A fully-qualified hostname for the IP address.
Note
IP addresses within the same subnet cannot be configured on separate physical Ethernet interfaces. See
for more detailed information on Network and IP
Address configuration.
Accepting Mail
When configuring your interfaces to accept mail, you define:
•
the domain for which to accept mail
•
destination (SMTP Route) for each domain, this is optional
Mark the checkbox for Accept Incoming Mail to configure the interface to accept mail. Enter the name
of the domain for which to accept mail.
of the domain for which to accept mail.
Enter the Destination. This is the SMTP Route or name of the machine(s) where you would like to route
email for the domains specified.
email for the domains specified.
This is the first SMTP Routes entry. The SMTP Routes table allows you to redirect all email for each
domain (also known as a Recipient Access Table (RAT) entry) you enter to a specific mail exchange
(MX) host. In typical installations, the SMTP Routes table defines the specific groupware (for example,
Microsoft Exchange) server or the “next hop” in the email delivery for your infrastructure.
domain (also known as a Recipient Access Table (RAT) entry) you enter to a specific mail exchange
(MX) host. In typical installations, the SMTP Routes table defines the specific groupware (for example,
Microsoft Exchange) server or the “next hop” in the email delivery for your infrastructure.
For example, you can define a route that specifies that mail accepted for the domain
example.com
and
all of its subdomains
.example.com
is routed the to the groupware server
exchange.example.com
.
You can enter multiple domains and destinations. Click Add Row to add another domain. Click the trash
can icon to remove a row.
can icon to remove a row.