Cisco Cisco Unity Express for SRE
Cisco ISR G2 Multi Gigabit Fabric
Configuring the MGF Interface on the Cisco SRE in Cisco IOS Release 15.1(3)T and Later Releases
6
Cisco ISR G2 Multi Gigabit Fabric
OL-24813-01
Restrictions
•
The MGF feature is only available for the following modules:
–
Cisco SRE ISM
–
Cisco SRE SM
–
Cisco Enhanced EtherSwitch Service Module (Cisco SM-ES and Cisco SM-ES-D)
•
If Cisco EtherSwitch HWIC and Cisco EtherSwitch Network Module are not present in the system,
no HIMI or VLAN connect is available for Cisco Enhanced EtherSwitch Service Module and SRE.
You cannot use HIMI or VLAN connect with any Cisco EtherSwitch Service Module module in the
system.
no HIMI or VLAN connect is available for Cisco Enhanced EtherSwitch Service Module and SRE.
You cannot use HIMI or VLAN connect with any Cisco EtherSwitch Service Module module in the
system.
•
The maximum number of VLANs is 64, not including the native VLAN.
•
SMs can only use VLAN 1 as the native VLAN. This native restriction does not apply to
Cisco Enhanced EtherSwitch Service Modules.
Cisco Enhanced EtherSwitch Service Modules.
•
PVDMs cannot communicate with other modules even if they are on the same VLAN.
Cisco Enhanced EtherSwitch Service Module and Cisco Gigabit EtherSwitch EHWIC ports can
communicate without external cabling. Only Cisco 1941s support WLAN.
Cisco Enhanced EtherSwitch Service Module and Cisco Gigabit EtherSwitch EHWIC ports can
communicate without external cabling. Only Cisco 1941s support WLAN.
•
The service-module mgf commands are visible only when the Linux application supports the MGF
feature. See your Linux application documentation to determine MGF support.
feature. See your Linux application documentation to determine MGF support.
•
Creating VLANs and storing them in the VLAN database is the same as having a legacy switch
module like the Cisco EtherSwitch HWIC and/or Cisco EtherSwitch Network Module.
module like the Cisco EtherSwitch HWIC and/or Cisco EtherSwitch Network Module.
•
If your router is running an earlier release of Cisco IOS than Cisco IOS Release 15.2(1)T,
Online Insertion and Removal (OIR) is not supported by the MGF feature on Cisco SRE SM,
Cisco SRE ISM, or Cisco Enhanced EtherSwitch Service Modules. When using one of these earlier
releases of Cisco IOS, you must reload the router after OIR.
Online Insertion and Removal (OIR) is not supported by the MGF feature on Cisco SRE SM,
Cisco SRE ISM, or Cisco Enhanced EtherSwitch Service Modules. When using one of these earlier
releases of Cisco IOS, you must reload the router after OIR.
Configuring the MGF Interface on the Cisco SRE in Cisco IOS
Release 15.1(3)T and Later Releases
Release 15.1(3)T and Later Releases
This deployment scenario in which the router has only Cisco SRE SM, Cisco SRE ISM, and/or
Cisco Enhanced EtherSwitch Service Modules is the most common.
Cisco Enhanced EtherSwitch Service Modules is the most common.
The native VLAN is configured when the SRE MGF port is configured as trunk. The default native
VLAN is VLAN 1. All VLAN configuration is performed on interface SM slot/1. Multiple IP addresses
must be assigned to each VLAN.
VLAN is VLAN 1. All VLAN configuration is performed on interface SM slot/1. Multiple IP addresses
must be assigned to each VLAN.
•
SUMMARY STEPS
From the Host-Router CLI
1.
enable
2.
configure terminal
3.
interface ism 0/0
or