Cisco Cisco MDS 9000 NX-OS Software Release 5.0 Notas de publicación
S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m
41
Cisco MDS 9000 Family Release Notes for Cisco MDS NX-OS Release 5.0(4)
OL-21012-02
Caveats
Mod Sw Hw World-Wide-Name(s) (WWN)
--- -------------- ------ --------------------------------------------------
2 5.2(1) <B>1.0</B> 20:41:00:0d:ec:24:f4:c0 to
20:58:00:0d:ec:24:f4:c0
In the preceding output, the device is hardware revision 1.0 and therefore not affected.
For the DS-X9304-18K9 and the DS-C9222i-K9, the show module command might indicate
hardware version 1.0 due to new part numbers; however the show sprom module command shows
the affected parts.
hardware version 1.0 due to new part numbers; however the show sprom module command shows
the affected parts.
switch# sh mod 9
Mod Ports Module-Type Model Status
--- ----- ----------------------------------- ------------------ ----------
9 22 4x1GE IPS, 18x1/2/4Gbps FC Module DS-X9304-18K9 ok
Mod Sw Hw World-Wide-Name(s) (WWN)
--- -------------- ------ --------------------------------------------------
9 5.2(1) 1.0 22:01:00:0d:ec:25:e9:80 to 22:12:00:0d:ec:25:e9:80
Mod MAC-Address(es) Serial-Num
--- -------------------------------------- ----------
9 00-1a-e2-03-4c-5c to 00-1a-e2-03-4c-64 JAE1131SCBW
switch# sh sprom module 9 1 |egrep "Part|Serial"
Serial Number : JAE1131SCBW
Part Number : 73-10688-06 <-- Not 73-14372-01 so h/w ver 1.0 is OK
Part Revision : A0
Workaround: Upgrade to software release that has the fix for this issue.
–
After performing a software upgrade to a Cisco NX-OS release that contains a fix for this issue,
it may be necessary to enter the shut command followed by the no shut command on the
affected host ports to regain connectivity.
it may be necessary to enter the shut command followed by the no shut command on the
affected host ports to regain connectivity.
–
If you perform a nondisruptive upgrade or downgrade from a release that contains a fix to a
release that does not contain the fix, you need to reload each module affected by this issue.
release that does not contain the fix, you need to reload each module affected by this issue.
–
If you have a Cisco MDS 9222i swtich that is affected by this issue, and you perform a
nondisruptive upgrade or downgrade from a release that contains a fix to a release that does not
contain the fix, you need to reload the switch.
nondisruptive upgrade or downgrade from a release that contains a fix to a release that does not
contain the fix, you need to reload the switch.
•
CSCsq20408
Symptom: The show startup command displays aspects of the running configuration when
SANTap is configured and/or SANTap objects are created. When a user creates objects such as a
CVT or DVT, the configuration is showing in the running-configuration and in the
startup-configuration without copying the configuration into the startup-configuration.
SANTap is configured and/or SANTap objects are created. When a user creates objects such as a
CVT or DVT, the configuration is showing in the running-configuration and in the
startup-configuration without copying the configuration into the startup-configuration.
Workaround: Issue a copy running-config startup-config command whenever you create objects
such as a CVT or DVT so that the running-configuration and startup-configuration are synchronized.
such as a CVT or DVT so that the running-configuration and startup-configuration are synchronized.
•
CSCtn68418
Symptom: When you try to save a configuration, you might see the following message:
switch# copy run start
[########################################] 100%
Configuration update aborted: request was aborted
%DAEMON-3-SYSTEM_MSG: ntp:can't open /mnt/pss/ntp.drift.TEMP: No space left on device
- ntpd[xxxx]
%PLATFORM-2-MEMORY_ALERT: Memory Status Alert : MINOR
%PLATFORM-2-MEMORY_ALERT: Memory Status Alert : MINOR ALERT RECOVERED