Cisco Cisco MDS 9000 NX-OS Software Release 4.1 Guía De Instalación
S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m .
8
Cisco MDS 9000 Family Storage Services Interface Image Installation and Upgrade Guide
OL-17262-03, Cisco MDS NX-OS Release 4.x
Cisco MDS 9000 Family Storage Services Interface Image Installation and Upgrade Guide
Upgrading to Cisco MDS SAN-OS Release 3.0(1) and Later
For Cisco MDS 9200 Series switches:
switch# delete bootflash:m9000-ek9-ssi-mz.2.1.2i.bin
Step 13
Save the configuration.
switch# copy running-config startup-config
For more information about upgrading Cisco SAN-OS on your MDS switch, refer to the
.
Upgrading to Cisco MDS SAN-OS Release 3.0(1) and Later
This section describes the procedure to upgrade your MDS switch from Cisco MDS SAN-OS Release
2.1(2b), or later, to Release 3.0(1), or later, and it includes the following actions:
2.1(2b), or later, to Release 3.0(1), or later, and it includes the following actions:
•
Place the kickstart and system images for both Cisco SAN-OS Release 2.1(2b), or later, and Release
3.0(1), or later, on the active supervisor module bootflash.
3.0(1), or later, on the active supervisor module bootflash.
•
Make sure that the standby supervisor module on Cisco MDS 9500 Series switches has at least the
kickstart and system images for Cisco SAN-OS Release 2.1(2b), or later, on the bootflash and has
enough free space for the Cisco SAN-OS Release 3.0(1), or later, kickstart and system images.
kickstart and system images for Cisco SAN-OS Release 2.1(2b), or later, on the bootflash and has
enough free space for the Cisco SAN-OS Release 3.0(1), or later, kickstart and system images.
•
Delete any unnecessary files on the standby supervisor module bootflash on a Cisco MDS 9500
Series switches.
Series switches.
Note
You must upgrade to Cisco SAN-OS Release 2.1(2b), or later, before upgrading to Cisco SAN-OS
Release 3.0(1).
Release 3.0(1).
Note
During the process of upgrading, the Cisco SAN-OS Release 3.0(1) or later, kickstart image and system
images are copied to the standby supervisor module bootflash on Cisco MDS 9500 Series switches.
images are copied to the standby supervisor module bootflash on Cisco MDS 9500 Series switches.
To upgrade your MDS switch to Cisco MDS SAN-OS Release 3.0(1), or later, follow these steps:
Step 1
Determine the correct SSI boot image version for the Cisco SAN-OS release to which you are upgrading
(See the
(See the
)
Note
You must obtain an SSI image that is compatible with the Cisco SAN-OS kickstart image and
system image for the MDS switch and SSMs to boot successfully.
system image for the MDS switch and SSMs to boot successfully.
Step 2
Obtain the kickstart image and system image for Cisco SAN-OS Release 3.0(1), or later, and the
appropriate SSI boot image from the Cisco.com software download site. This site also shows the size of
the image files in byte:
appropriate SSI boot image from the Cisco.com software download site. This site also shows the size of
the image files in byte:
Step 3
Verify that SSI boot images for all SSMs on the switch are installed on the modflash on each SSM. (See
the
the
Step 4
Verify that there is available space on the active supervisor module bootflash for the image files.