Cisco Cisco IOS Software Release 12.4(23) Notas de publicación
29
Release Notes for Cisco IOS Release 12.4
OL-7661-15
Platform-Specific Information
The Cisco 1760 router supports any combination of one or two of the following voice interface cards
(VICs), which are shared with the Cisco 2600 and Cisco 3600 series routers:
(VICs), which are shared with the Cisco 2600 and Cisco 3600 series routers:
•
VIC-2FXS: Two-port Foreign Exchange Station (FXS) voice/fax interface card for voice/fax
network module.
network module.
•
VIC-2FXO: Two-port Foreign Exchange Office (FXO) voice/fax interface card for voice/fax
network module.
network module.
•
VIC-2FXO-EU: Two-port FXO voice/fax interface card for Europe.
•
VIC-2E/M: Two-port Ear-and-Mouth (E&M) voice/fax interface card for voice/fax network module.
•
VIC2-2BRI-NT/TE: Two-port voice interface card, BRI (NT and TE).
•
VIC-2FXO-M3: Two-port FXO voice/fax interface card for Australia.
•
VIC-2FXO-M1: Two-port FXO voice/fax interface card with battery reversal (for North America).
•
VIC-2FXO-M2: Two-port FXO voice/fax interface card with battery reversal (for Europe).
•
VIC-2DID: Two-port Direct Inward Dial voice/fax interface card.
•
VIC-4FXS/DID: Four-port FXS or DID VIC.
•
VIC2-2FXS: Two-port voice interface card, FXS.
•
VIC2-2FXO: Two-port voice interface card, FXO (universal).
•
VIC2-4FXO: Four-port voice interface card, FXO (universal).
•
VIC-2BRI-NT/TE: Two-port voice/fax interface card (BRI [NT and TE]).
Feature Support
For feature support in Cisco IOS Release 12.4, see the
.
Additional Notes for the Cisco 1700 Series Routers
This section contains important information about using the Cisco 1700 series routers with Cisco IOS
Release 12.4 software.
Release 12.4 software.
SmartInit
The following points must be observed while using SmartInit:
•
If the user has configured the no memory-size iomem command from a pre-SmartInit image (old
image) and a SmartInit image is loaded on the router, the router will boot with SmartInit enabled.
The running configuration will not display any memory-size iomem command-line interface (CLI)
commands.
image) and a SmartInit image is loaded on the router, the router will boot with SmartInit enabled.
The running configuration will not display any memory-size iomem command-line interface (CLI)
commands.
•
If the user has configured the memory-size iomem 10 command from a pre-SmartInit image and a
SmartInit image is loaded on the router, the router will boot with SmartInit enabled. Consequently,
the I/O memory size may not be 10 percent (as expected on a pre-SmartInit image).
SmartInit image is loaded on the router, the router will boot with SmartInit enabled. Consequently,
the I/O memory size may not be 10 percent (as expected on a pre-SmartInit image).
•
If the user configures the memory-size iomem 10 command on a SmartInit image, it will be
displayed in the running and startup configurations. This is different from the pre-SmartInit that
does not display the memory-size iomem 10 command because 10 percent is the default I/O
memory size.
displayed in the running and startup configurations. This is different from the pre-SmartInit that
does not display the memory-size iomem 10 command because 10 percent is the default I/O
memory size.