Cisco Cisco Aironet 1530i Outdoor Access Point Notas de publicación
13
Release Notes for Cisco Aironet Access Points and Bridges for Cisco IOS Release 15.3(3)JA1
OL-31537-01
Important Notes
When you connect a 1040, 1130, 1140, 1250, or 1260 series access point or a 1300 series outdoor access
point/bridge with a default configuration to a LAN, the access point requests an IP address from a DHCP
server and, if it does not receive an address, continues to send requests indefinitely.
point/bridge with a default configuration to a LAN, the access point requests an IP address from a DHCP
server and, if it does not receive an address, continues to send requests indefinitely.
Changes to the Default Configuration—Radios Disabled and No Default SSID
The radio or radios are disabled by default, and there is no default SSID. You must create an SSID and
enable the radio or radios before the access point allows wireless associations from other devices. These
changes to the default configuration improve the security of newly installed access points.
enable the radio or radios before the access point allows wireless associations from other devices. These
changes to the default configuration improve the security of newly installed access points.
Clients Using WPA/WPA2 and Power Save May Fail to Authenticate
Certain clients using WPA/WPA2 key management and power save can take many attempts to
authenticate or, in some cases, fail to authenticate. Any SSID that is defined to use authentication
key-management WPA, together with clients using power save mode and authenticating using
WPA/WPA2, can experience this problem.
authenticate or, in some cases, fail to authenticate. Any SSID that is defined to use authentication
key-management WPA, together with clients using power save mode and authenticating using
WPA/WPA2, can experience this problem.
A hidden configure level command, dot11 wpa handshake timeout, can be used to increase the timeout
between sending the WPA key packets from the default value (100 ms) to a value between 101 and 2000
ms. The command stores its value in the configuration across device reloads.
between sending the WPA key packets from the default value (100 ms) to a value between 101 and 2000
ms. The command stores its value in the configuration across device reloads.
Default Username and Password Are Cisco
When you open the access point interface, you must enter a username and a password. The default
username for administrator login is Cisco, and the default password is Cisco. Both the username and
password are case sensitive.
username for administrator login is Cisco, and the default password is Cisco. Both the username and
password are case sensitive.
Some Client Devices Cannot Associate When QoS Is Configured
Some wireless client devices, including Dell Axim handhelds and Hewlett-Packard iPaq HX4700
handhelds, cannot associate to an access point when the access point is configured for QoS. To allow
these clients to associate, disable QoS on the access point. You can use the QoS Policies page on the
access point GUI to disable QoS or enter this command on the CLI:
handhelds, cannot associate to an access point when the access point is configured for QoS. To allow
these clients to associate, disable QoS on the access point. You can use the QoS Policies page on the
access point GUI to disable QoS or enter this command on the CLI:
ap(config-if)# no dot11 qos mode
Some Devices Disassociate When Multiple BSSIDs Are Added or Deleted
Devices on your wireless LAN that are configured to associate to a specific access point based on the
access point MAC address (such as client devices, repeaters, hot standby units, or workgroup bridges)
might lose their association when you add or delete multiple BSSIDs. When you add or delete multiple
BSSIDs, check the association status of devices that are configured to associate to a specific access
point. If necessary, reconfigure the disassociated device to use the BSSID new MAC address.
access point MAC address (such as client devices, repeaters, hot standby units, or workgroup bridges)
might lose their association when you add or delete multiple BSSIDs. When you add or delete multiple
BSSIDs, check the association status of devices that are configured to associate to a specific access
point. If necessary, reconfigure the disassociated device to use the BSSID new MAC address.