Cisco Cisco Aironet 1130 AG Access Point Notas de publicación
5
Release Notes for Cisco Aironet Access Points for Cisco IOS Release 12.3(8)JEA
OL-11186-01
System Requirements
Converting to Cisco IOS Software
If your 350 or 1200 series access point does not run IOS software, you can use the conversion utility or
the conversion upgrade image to convert the access point system to IOS software. Use the conversion
utility to maintain the current configuration after the conversion, or load the upgrade image to convert
to IOS software without saving the current configuration. Your access point must be running one of these
VxWorks firmware versions before you can convert to IOS software:
the conversion upgrade image to convert the access point system to IOS software. Use the conversion
utility to maintain the current configuration after the conversion, or load the upgrade image to convert
to IOS software without saving the current configuration. Your access point must be running one of these
VxWorks firmware versions before you can convert to IOS software:
•
350 series access points must be running VxWorks version 12.03T, 12.02T1, 12.01T1, 11.23T, or
11.21
11.21
•
1200 series access points must be running VxWorks version 12.03T, 12.02T1, 12.01T1, 12.00T,
11.56, or 11.54T
11.56, or 11.54T
The conversion upgrade image for 350 series access points installs Cisco IOS Release 12.2(13)JA1 on
your 350 series access point. The conversion upgrade image for 1200 series access points installs Cisco
IOS Release 12.2(13)JA2 on your 1200 series access point.
your 350 series access point. The conversion upgrade image for 1200 series access points installs Cisco
IOS Release 12.2(13)JA2 on your 1200 series access point.
Note
The upgrade image and the conversion tool do not support VxWorks version 12.04. Access points
running version 12.04 must be downgraded to a supported operating system version before you can use
the upgrade image or the conversion tool.
running version 12.04 must be downgraded to a supported operating system version before you can use
the upgrade image or the conversion tool.
Note
The upgrade to Cisco IOS software is permanent; you cannot revert to non-IOS software. Product
warranties do not cover unintended upgrades.
warranties do not cover unintended upgrades.
For complete instructions on using the conversion utility, refer to the Cisco Aironet Conversion Tool for
Cisco IOS Software, 2.1 Administrator Guide for Windows. Click this link to browse to the Administrator
Guide:
Cisco IOS Software, 2.1 Administrator Guide for Windows. Click this link to browse to the Administrator
Guide:
To download the conversion utility or the upgrade image, click this link to browse to the Cisco IOS
Software Center on Cisco.com:
Software Center on Cisco.com:
On the Cisco IOS Software Center page, enter your Cisco.com username and password to use the Feature
Navigator or the Cisco IOS Upgrade Planner, or click Wireless Software to go to the Wireless LAN
Software page. Download the conversion utility or the upgrade image for 350 or 1200 series access
points. You can also download instructions for using the utility and the image.
Navigator or the Cisco IOS Upgrade Planner, or click Wireless Software to go to the Wireless LAN
Software page. Download the conversion utility or the upgrade image for 350 or 1200 series access
points. You can also download instructions for using the utility and the image.
Some Fields Not Updated During Upgrade to IOS Software
When you upgrade an access point to run Cisco IOS software, some fields that are reported in the console
messages during the upgrade are blank or are populated with zeros. However, blank or zero fields are
normal after a successful upgrade, because 350 and 1200 series access points do not support that
information. This example shows fields that might appear blank or populated with zeros:
messages during the upgrade are blank or are populated with zeros. However, blank or zero fields are
normal after a successful upgrade, because 350 and 1200 series access points do not support that
information. This example shows fields that might appear blank or populated with zeros:
32K bytes of flash-simulated non-volatile configuration memory.
Base Ethernet MAC Address: 00:05:9A:38:42:91
Part Number: 0-0000-00
PCA Assembly Number: 000-00000-00
PCA Revision Number:
PCB Serial Number: