Cisco Cisco Aironet 1400 Wireless Bridge Guía De Instalación
![Cisco](https://files.manualsbrain.com/attachments/7380d0050044647c30f5c24bbbf5d0c0b6d9bb84/common/fit/150/50/faa183d287233c52228cfea3dbc2a127fe780f60564fcb0955d9c3d1cd23/brand_logo.png)
6
Cisco Aironet 1400 Series Outdoor Wireless Bridge 28-dBi Dish Antenna
78-15547-01
Installation Notes
Mounting the Antenna
A mounting kit is provided with the antenna. This kit enables you to mount the antenna to masts up to
2.5 in. (6.3 cm) in diameter. The antenna can be vertically or horizontally polarized, but it must be
mounted so that the parabola is in the vertical plane.
2.5 in. (6.3 cm) in diameter. The antenna can be vertically or horizontally polarized, but it must be
mounted so that the parabola is in the vertical plane.
Note
To meet regulatory restrictions, the external antenna model of the bridge and its external antenna must
be professionally installed.
be professionally installed.
Note
To ensure correct installation and grounding, install the antenna in compliance with your local and
national electrical codes: National Fire Protection Association (NFPA) 70, National Electrical Code
(U.S.); Canadian Electrical Code, Part 1, CSA22.1 (Canada); and if local or are not available, refer to
IEC 364, Part 1 through Part 7 (other countries).
national electrical codes: National Fire Protection Association (NFPA) 70, National Electrical Code
(U.S.); Canadian Electrical Code, Part 1, CSA22.1 (Canada); and if local or are not available, refer to
IEC 364, Part 1 through Part 7 (other countries).
Adjusting Polarization
A decal is attached to the star mounting plate indicating how the antenna should be mounted for vertical
polarization. To obtain vertical polarization, mount the antenna so that the arrow on the decal is pointing
up. To obtain horizontal polarization, rotate the antenna clockwise 90 degrees so that arrow on the decal
is pointing to the right (at the 3 o’clock position).
polarization. To obtain vertical polarization, mount the antenna so that the arrow on the decal is pointing
up. To obtain horizontal polarization, rotate the antenna clockwise 90 degrees so that arrow on the decal
is pointing to the right (at the 3 o’clock position).
Note
The antennas of any two units that are intended to form a link and associate with one another must be
set for the same polarization.
set for the same polarization.
Mounting the Antenna to a Mast
Follow these steps to mount the antenna to a mast.
Step 1
Remove the four #10 cap screws, lock washers, and flat washers from the mounting kit’s hardware bag.
Step 2
Position the feed tube as shown in Figure 1, aligning the polarization pin on the feed tube with the hole
in the dish.
in the dish.
Step 3
Insert cable through the hole and install screws with a 5/32-in. (4-mm) long shank hex key and tighten.
Be sure to install the lock and flat washers. Do not overtighten.
Be sure to install the lock and flat washers. Do not overtighten.
Step 4
Position the connector through the slot on the square tube section of the mount structure and secure it in
place using a lock washer and jam nut.
place using a lock washer and jam nut.
Step 5
Remove two U-bolts, V-blocks, and four 3/8-in. (10-mm) hex nuts, lock washers, and flat washers from
the hardware bag.
the hardware bag.
Step 6
Determine the antenna polarization for your installation and position the antenna appropriately:
a.
Vertical: the arrow on the decal is pointing up.
b.
Horizontal: the arrow on the decal is pointing to the right (at the 3 o’clock position).