Cisco Cisco Aironet 1310 Access Point Bridge Notas de publicación
11
Release Notes for Cisco Aironet 1300 Series Outdoor Access Point/Bridge for Cisco IOS Release 12.3(4)JA2
OL-8216-01
Important Notes
Non-Cisco Aironet Clients Sometimes Fail 802.1x Authentication
Some non-Cisco Aironet client adapters do not perform 802.1x authentication to the access point/bridge
unless you configure Open authentication with EAP. To allow both Cisco Aironet clients using LEAP
and non-Cisco Aironet clients using LEAP to associate using the same SSID, you might need to
configure the SSID for both Network EAP authentication and Open authentication with EAP.
unless you configure Open authentication with EAP. To allow both Cisco Aironet clients using LEAP
and non-Cisco Aironet clients using LEAP to associate using the same SSID, you might need to
configure the SSID for both Network EAP authentication and Open authentication with EAP.
Pings and Link Tests Sometimes Fail to Clients with both Wired and Wireless
Network Connections
Network Connections
When you ping or run a link test from an access point to a client device installed in a PC running
Microsoft Windows 2000, the ping or link test sometimes fails when the client has both wired and
wireless connections to the LAN. Microsoft does not recommend this configuration. For more
information, refer to Microsoft Knowledge Base article 157025 at this URL:
Microsoft Windows 2000, the ping or link test sometimes fails when the client has both wired and
wireless connections to the LAN. Microsoft does not recommend this configuration. For more
information, refer to Microsoft Knowledge Base article 157025 at this URL:
Limitation to PAgP Redundancy on Switches Connected by Bridge Links
When running PAgP on switched connected to series bridges, for ethernet traffic redundancy and load
balance be aware that PAgP switchover takes at least 30 seconds, which is too slow to maintain certain
traffic (for example, TCP) when switching from port to the other. There is no workaround for this
limitation.
balance be aware that PAgP switchover takes at least 30 seconds, which is too slow to maintain certain
traffic (for example, TCP) when switching from port to the other. There is no workaround for this
limitation.
Default IP Address Behavior
When an unconfigured access point/bridge boots, it attempts to obtain an IP address from a DHCP server.
If it fails to locate a DHCP server, it continues attempting to request an IP address from the DHCP server.
To eliminate this behavior, you must access the access point/bridge through its console port and assign
a static IP address.
If it fails to locate a DHCP server, it continues attempting to request an IP address from the DHCP server.
To eliminate this behavior, you must access the access point/bridge through its console port and assign
a static IP address.
If you want to reset the access point/bridge to its default settings and a static IP address, use the write
erase or erase /all nvram command. If you want to erase everything including the static IP address, in
addition to the above commands, use the erase and erase boot static-ipaddr static-ipmask command.
erase or erase /all nvram command. If you want to erase everything including the static IP address, in
addition to the above commands, use the erase and erase boot static-ipaddr static-ipmask command.
Caution
You should never delete any of the system files prior to resetting defaults or reloading software.
Ethernet Duplex Settings
The access point/bridge is implemented with an unmanaged and unconfigurable 10/100BASET switch
embedded in the power injector. All ports on the switch are set for auto-speed, auto-duplex, and
auto-MDIX. Port 0 on the switch is used for the coaxial link to the access point/bridge. Port 1 on the
switch is used for the RJ 45 jack on the power injector.
embedded in the power injector. All ports on the switch are set for auto-speed, auto-duplex, and
auto-MDIX. Port 0 on the switch is used for the coaxial link to the access point/bridge. Port 1 on the
switch is used for the RJ 45 jack on the power injector.