Cisco Cisco Aironet 1310 Access Point Bridge Notas de publicación
8
Release Notes for Cisco Aironet Access Points for Cisco IOS Release 12.3(8)JEA1
OL-12427-01
Installation Notes
Using a Switch Capable of IEEE 802.3af Power Negotiation
If you use a switch to provide Power over Ethernet (PoE) to the access point and the switch supports the
IEEE 802.3af power negotiation standard, select Power Negotiation on the System Software: System
Configuration page.
IEEE 802.3af power negotiation standard, select Power Negotiation on the System Software: System
Configuration page.
Using a Switch That Does Not Support IEEE 802.3af Power Negotiation
If you use a switch to provide Power over Ethernet (PoE) to the access point and the switch does not
support the IEEE 802.3af power negotiation standard, select Pre-Standard Compatibility on the
System Software: System Configuration page.
support the IEEE 802.3af power negotiation standard, select Pre-Standard Compatibility on the
System Software: System Configuration page.
Using a Power Injector
If you use a power injector to provide power to the access point, select Power Injector on the System
Software: System Configuration page and enter the MAC address of the switch port to which the access
point is connected.
Software: System Configuration page and enter the MAC address of the switch port to which the access
point is connected.
Operating 5-GHz Radio Requires Power Injector, Power Module, or Catalyst 3550-24 PWR Switch
The 1200 series power injector and the 1200 series power module support operation of the 5-GHz radio
in the access point. Currently, the Catalyst 3550-24 PWR switch supports power for both the 2.4-GHz
radio and the 5-GHz radio. Other switches and power patch panels might not provide enough power for
the 5-GHz radio.
in the access point. Currently, the Catalyst 3550-24 PWR switch supports power for both the 2.4-GHz
radio and the 5-GHz radio. Other switches and power patch panels might not provide enough power for
the 5-GHz radio.
Access Point Requires 1200 Series Universal Power Supply and Power Injector
If you use a power injector or a power module to provide power to a 1200 series access point, you must
use a 1200 series universal power supply. If you need to use a power injector to inject power into the
access point’s Ethernet port, you must use a 1200 series power injector.
use a 1200 series universal power supply. If you need to use a power injector to inject power into the
access point’s Ethernet port, you must use a 1200 series power injector.
Unpowered 1100 Series Access Points Cause Loopback When Connected to Switches Without
Loopback Detection
Loopback Detection
When you connect an unpowered 1100 series access point to a switch without loopback detection, the
access point causes a loopback. To avoid this problem, make sure loopback detection is enabled on the
switch to which the access point is connected. If your switch does not have loopback detection,
disconnect the access point from the switch when the access point power is off.
access point causes a loopback. To avoid this problem, make sure loopback detection is enabled on the
switch to which the access point is connected. If your switch does not have loopback detection,
disconnect the access point from the switch when the access point power is off.
Antenna Installation
For instructions on the proper installation and grounding of external antennas for 1200, and 1240 series
access points, refer to the National Fire Protection Association’s NFPA 70, National Electrical Code,
Article 810, and the Canadian Standards Association’s Canadian Electrical Code, Section 54.
access points, refer to the National Fire Protection Association’s NFPA 70, National Electrical Code,
Article 810, and the Canadian Standards Association’s Canadian Electrical Code, Section 54.
Warning
Do not install the antenna near overhead power lines or other electric light or power circuits, or
where it can come into contact with such circuits. When installing the antenna, take extreme care
not to come into contact with such circuits, as they may cause serious injury or death.
where it can come into contact with such circuits. When installing the antenna, take extreme care
not to come into contact with such circuits, as they may cause serious injury or death.