Cisco Cisco Aironet 1310 Access Point Bridge Notas de publicación
10
Release Notes for Cisco Aironet 1310 Outdoor Access Point/Bridge for Cisco IOS Release 12.3(2)JA2
OL-6723-02
Important Notes
Mask Field on IP Filters Page Behaves the Same As in CLI
In Cisco IOS Release 12.2(8)JA and later, the mask that you enter in the Mask field on the IP Filters page
in the 1310 access point/bridge GUI behaves the same way as a mask that you enter in the CLI. If you
enter 255.255.255.255 as the mask, the 1310 access point/bridge accepts any IP address. If you enter
0.0.0.0, the 1310 access point/bridge looks for an exact match with the IP address that you entered in the
IP Address field.
in the 1310 access point/bridge GUI behaves the same way as a mask that you enter in the CLI. If you
enter 255.255.255.255 as the mask, the 1310 access point/bridge accepts any IP address. If you enter
0.0.0.0, the 1310 access point/bridge looks for an exact match with the IP address that you entered in the
IP Address field.
System Software Upgrade Sometimes Fails Using Microsoft Internet Explorer
5.01 SP2
5.01 SP2
A system software upgrade sometimes fails when you use Microsoft Internet Explorer version 5.01 SP2
to upgrade system software using the HTTP Upgrade page in the web-browser interface. Use a later
version of Microsoft Internet Explorer to perform HTTP system software upgrades, or use TFTP to
upgrade system software. Click this URL to browse to the Cisco 1300 Series Wireless Bridge Software
Configuration Guide for complete instructions on performing software upgrades:
to upgrade system software using the HTTP Upgrade page in the web-browser interface. Use a later
version of Microsoft Internet Explorer to perform HTTP system software upgrades, or use TFTP to
upgrade system software. Click this URL to browse to the Cisco 1300 Series Wireless Bridge Software
Configuration Guide for complete instructions on performing software upgrades:
Corrupt EAP Packet Sometimes Causes Error Message
During client authentication, the 1310 access point/bridge sometimes receives a corrupt EAP packet and
displays this error message:
displays this error message:
Oct 1 09:00:51.642 R: %SYS-2-GETBUF: Bad getbuffer, bytes= 28165
-Process= "Dot11 Dot1x process", ipl= 0, pid= 32
-Traceback= A2F98 3C441C 3C7184 3C604C 3C5E14 3C5430 124DDC
You can ignore these messages.
When Cipher is TKIP Only, Key Management Must Be Enabled
When “Cipher TKIP” is configured on a VLAN, the SSID(s) for that VLAN must use WPA or CCKM
key management. If you do not configure the SSID(s) for that VLAN with WPA or CCKM, client
authentication fails on the SSIDs.
key management. If you do not configure the SSID(s) for that VLAN with WPA or CCKM, client
authentication fails on the SSIDs.
Non-Cisco Aironet Clients Sometimes Fail 802.1x Authentication
Some non-Cisco Aironet client adapters do not perform 802.1x authentication to the 1310 access
point/bridge unless you configure Open authentication with EAP. To allow both Cisco Aironet clients
using LEAP and non-Cisco Aironet clients using LEAP to associate using the same SSID, you might
need to configure the SSID for both Network EAP authentication and Open authentication with EAP.
point/bridge unless you configure Open authentication with EAP. To allow both Cisco Aironet clients
using LEAP and non-Cisco Aironet clients using LEAP to associate using the same SSID, you might
need to configure the SSID for both Network EAP authentication and Open authentication with EAP.