Cisco Cisco Aironet 350 Access Points Notas de publicación
17
Release Notes for Cisco Aironet 350, 1100, and 1200 Series Access Points for Cisco IOS Release 12.2(13)JA2
OL-5428-01
Caveats
•
CSCeb36095—Access points running Cisco IOS software now send the same RADIUS
NAS-port-type value as access points running VxWorks.
NAS-port-type value as access points running VxWorks.
•
CSCeb36192—The access point now assigns user VLANs correctly whether or not multiple SSIDs
are configured.
are configured.
•
CSCeb39541—The default EAP client timeout (the length of time that the access point waits for a
client to respond to the access point’s EAP request) has changed from 10 seconds to 30 seconds.
client to respond to the access point’s EAP request) has changed from 10 seconds to 30 seconds.
•
CSCeb47892—You can now use the web-browser interface to disable the access point radio after
setting the role in radio network to Access Point Root (Fallback to Radio Shutdown).
setting the role in radio network to Access Point Root (Fallback to Radio Shutdown).
•
CSCeb48645—Client devices in power-save mode no longer lock up when associated to an access
point running Cisco IOS software.
point running Cisco IOS software.
•
CSCeb52239, CSCec20465—The access point now correctly assigns VLANs to devices connected
to a workgroup bridge.
to a workgroup bridge.
•
CSCeb60581—The access point now sends the correct username with RADIUS accounting packets.
•
CSCeb69596—You can now enter the letters in MAC addresses using either upper-case or
lower-case letters when using the web-browser interface to configure MAC-address filtering or
authentication.
lower-case letters when using the web-browser interface to configure MAC-address filtering or
authentication.
•
CSCeb76171—The web-browser interface now displays pages correctly when a message-of-the-day
(MOTD) banner is configured on the CLI.
(MOTD) banner is configured on the CLI.
•
CSCeb79465—The access point with a spectralink wireless phone now sends buffered data.
•
CSCeb87628—Client devices using PEAP authentication now authenticate successfully through the
access point.
access point.
•
CSCeb87982—The access point now correctly displays hot standby status and event messages.
•
CSCec00308—Efficient Speedstream DHCP server now responds to Cisco IOS DHCP discover
packets.
packets.
•
CSCec07703—Cisco 7920 IP Phones no longer drop calls when associated to 1100 and 1200 series
access points.
access points.
•
CSCec12813—Client devices in power-save mode no longer lose packets when they wake up.
•
CSCec15572—You can now use the [no] boot upgrade global configuration command to configure
the access point to boot without loading a configuration.
the access point to boot without loading a configuration.
•
CSCec21082—The access point now reports accurate statistics for ifOutUcastPkts on radio
interfaces.
interfaces.
•
CSCec29293—The access point no longer immediately drops all client associations when you enter
the reload in minutes command.
the reload in minutes command.
•
CSCec39405—The following combination of radio settings no longer reduces throughput on the
802.11a radio in 1200 series access points:
802.11a radio in 1200 series access points:
–
Fragmentation threshold set to 500
–
RTS threshold set to 256
–
WPA enabled
•
CSCec43028—The access point CLI no longer displays 40-bit WEP keys as 128-bit WEP keys.
•
CSCin44512—If 8 or more VLANs are configured on your access point, you can now apply filters
using the Apply Filters page in the web-browser interface.
using the Apply Filters page in the web-browser interface.
•
CSCin44591—PSPF now works when you use the web-browser interface to enable PSPF on a
non-native VLAN.
non-native VLAN.