Cisco Cisco WET200 Wireless-G Business Ethernet Bridge Manual De Mantenimiento
Chapter 6
Advanced Configuration
9
Wireless-G Business Ethernet Bridge
Chapter 6:
Advanced Configuration
Advanced Configuration
Open your web browser, enter http://192.168.1.226 in
the Address field, and press the Enter key.
the Address field, and press the Enter key.
Address Bar
NOTE:
The default IP address is 192.168.1.226.
If the IP address is changed using DHCP, enter
the assigned IP address instead of the default.
the assigned IP address instead of the default.
The web-based utiity’s login screen appears. The first time
you open the utility, enter admin (the default username)
in the username field, enter admin in the password field,
then click OK. You can change the username and password
later from the Administration tab’s Password screen.
you open the utility, enter admin (the default username)
in the username field, enter admin in the password field,
then click OK. You can change the username and password
later from the Administration tab’s Password screen.
Login Screen
After you log in, the Setup screen appears. To access other
screens, select one of the five tabs at the top of the screen:
Setup, Wireless, Switch, Administration, and System
Status. Each tab contains additional screens. These tabs
and their screens are explained in detail below.
screens, select one of the five tabs at the top of the screen:
Setup, Wireless, Switch, Administration, and System
Status. Each tab contains additional screens. These tabs
and their screens are explained in detail below.
Setup
The Setup tab contains one screen, the Setup screen. The
Setup screen contains basic information for the Bridge.
Setup screen contains basic information for the Bridge.
Host Name
This is the host name assigned to the Bridge.
This host name will be published to your DNS server if
the Bridge is configured to acquire its IP address through
DHCP. In that case, Linksys recommends following
company policy for host name assignment. The default
name is Linksys.
the Bridge is configured to acquire its IP address through
DHCP. In that case, Linksys recommends following
company policy for host name assignment. The default
name is Linksys.
Device Name
You may assign any device name to the
Bridge. This name is used only by the Bridge administrator
for identification purposes. Unique, memorable names
are helpful. The default name is WET200.
for identification purposes. Unique, memorable names
are helpful. The default name is WET200.
Contact
Enter the name of the administrator responsible
for the system.
Location
This field is used for entering a description of
where the Bridge is located, such as 3rd floor.
IP Address Type
Select how the WET200 will obtain its IP
address, either Static IP Address (default) or Automatic
Configuration-DHCP.
Configuration-DHCP.
Automatic Configuration-DHCP
•
The WET200 will
obtain its IP address automatically from a DHCP server.
NOTE:
If the DHCP server is not connected to
the Bridge ports but will be accessed via the
wireless interface, you must first create a wireless
connection before attempting to enable DHCP
on the WET200. Otherwise, the device will not
be able to obtain an IP address and the web-
based utility will be inaccessible. For detailed
information on creating a wireless connection,
see the “Wireless > Basic settings” section.
wireless interface, you must first create a wireless
connection before attempting to enable DHCP
on the WET200. Otherwise, the device will not
be able to obtain an IP address and the web-
based utility will be inaccessible. For detailed
information on creating a wireless connection,
see the “Wireless > Basic settings” section.
Static IP Address
•
To assign a static IP address to
the Bridge, select this option and fill in the IP Settings
fields. You should make sure that this IP address does
not conflict with the IP addresses of any other devices
on the network.
fields. You should make sure that this IP address does
not conflict with the IP addresses of any other devices
on the network.
IP Settings
If you set the IP Address Type field to Static IP
Address, complete the following fields.
Local IP Address
•
Enter the IP address of the Bridge
(default 192.168.1.226) into this field.
Subnet Mask
•
Enter the subnet mask into this field.
Default Gateway
•
IP address of the gateway router
(default 0.0.0.0) on the current IP subnet, used to
reach other IP networks.
reach other IP networks.
Primary DNS Server
•
Enter the IP address of the DNS
server (default 0.0.0.0) into the field.
Secondary DNS Server
•
A second DNS address
(default 0.0.0.0) can be specified in this field.
Setup Screen