Cisco Cisco WET200 Wireless-G Business Ethernet Bridge Manual De Mantenimiento
Chapter 6
Advanced Configuration
18
Wireless-G Business Ethernet Bridge
Switch > MAC Table
Use this screen to configure the MAC address table for
the switch. The MAC table is used to switch frames to the
correct ports. Before the MAC table is populated, a frame
is broadcast to all ports. Learning mode is enabled, then
the MAC table is populated automatically.
the switch. The MAC table is used to switch frames to the
correct ports. Before the MAC table is populated, a frame
is broadcast to all ports. Learning mode is enabled, then
the MAC table is populated automatically.
Switch > MAC Table
Global ATU Setting
This is a global MAC address table
setting. Select the desired settings, then click Apply
Global Setting.
Global Setting.
Address Learning
•
This indicates if the switch should
automatically learn the MAC address of packets. Select
Enable Learning (default) or Disable Learning.
Enable Learning (default) or Disable Learning.
Age timer
•
Detects and purges obsolete table entries,
such as when a connected device moves from one port
to another, by checking the idle timeout value of the
entries. The range is from 1 to 300 seconds. You can
also disable this feature. The default is 300 seconds.
to another, by checking the idle timeout value of the
entries. The range is from 1 to 300 seconds. You can
also disable this feature. The default is 300 seconds.
Static MAC Entry
Besides dynamically learned entries,
the MAC table can also contain static, user-defined entries
that you enter here. The MAC Address field shows the
destination MAC address. The check boxes specify the
output ports (1-5 and Wireless) where a packet is routed
if its destination MAC address matches the MAC Address
field. You can specify more than one output port. To add
an entry, enter the destination MAC address, select the
output port(s), and click Add New Entry. The new entry
will then appear in the Status Address Table list. Note that
static MAC entries are not affected by the Age timer and
can only be deleted manually.
that you enter here. The MAC Address field shows the
destination MAC address. The check boxes specify the
output ports (1-5 and Wireless) where a packet is routed
if its destination MAC address matches the MAC Address
field. You can specify more than one output port. To add
an entry, enter the destination MAC address, select the
output port(s), and click Add New Entry. The new entry
will then appear in the Status Address Table list. Note that
static MAC entries are not affected by the Age timer and
can only be deleted manually.
Static Address Table
This lists the static MAC address
entries and their port vector settings. To delete an entry,
select its check box and click Delete Selected Entry.
select its check box and click Delete Selected Entry.
Address Table Dump
A complete dump of the MAC
address table, including both learned and static entries.
If a topology change occurs, click Refresh to remove the
learned entries and force the entries to be relearned. At
most 64 entries are displayed per page. If there are more
than 64 entries, click Get Next Page to see more entries.
If a topology change occurs, click Refresh to remove the
learned entries and force the entries to be relearned. At
most 64 entries are displayed per page. If there are more
than 64 entries, click Get Next Page to see more entries.
Administration
The Administration tab is used for various administrative
tasks, such as to change the login password, configure
SNMP, save and restore system configuration, restore the
factory default settings, and upgrade the firmware.
tasks, such as to change the login password, configure
SNMP, save and restore system configuration, restore the
factory default settings, and upgrade the firmware.
Administration > Password
This screen allows you to change the username and/or
password for the Bridge. It is recommended that you
change the password from its default setting, admin.
password for the Bridge. It is recommended that you
change the password from its default setting, admin.
Administration > Password
User Name
The current user name is displayed (default
admin). To change the user name, enter the new user
name.
name.
Administrative Password
Enter a new password from 4
to 63 characters in length.
Re-enter to confirm
Enter password again to confirm.
Click Apply to apply your changes, or click Cancel to
cancel your changes.
cancel your changes.
Administration > Web Access
This screen allows you to enable or disable https access
to the utility.
to the utility.
Administration > Web Access