Cisco Cisco Aironet 1700i Access Points Notas de publicación
6
Release Notes for Cisco Aironet Access Points and Bridges for Cisco IOS Release 15.3(3)JA3
New Features and Platforms in this Release
Supported Browsers
These browsers are supported:
•
Internet Explorer 8.x and later
•
Firefox 3.x and later
New Features and Platforms in this Release
This section lists the new features and supported platforms in Cisco IOS Release 15.3(3)JA3.
Support for New Access Point Platforms
This release supports the following new access point platforms:
•
Support for Cisco Aironet 700W Series access point:
–
This 802.11n dual band access point is built on 2x2:2(2.4GHz), 2x2:2(5GHz) MIMO
technology, The access point is designed to be wall plate-mounted in indoor environments, and
has internal antennas.
technology, The access point is designed to be wall plate-mounted in indoor environments, and
has internal antennas.
–
This access point has one 10/100/1000BASE-T PoE Uplink/WAN port and four
10/100/1000BASE-T RJ-45 local Ethernet ports for wired device connectivity. The fourth port
functions as a PoE-Out port when the AP is powered by 802.3at Ethernet switch, Cisco power
injector AIR-PWRJ4=, or Cisco Power Supply.
10/100/1000BASE-T RJ-45 local Ethernet ports for wired device connectivity. The fourth port
functions as a PoE-Out port when the AP is powered by 802.3at Ethernet switch, Cisco power
injector AIR-PWRJ4=, or Cisco Power Supply.
–
By default, all four local Ethernet ports are disabled. You can be enable them when required.
–
The LED status display is disabled by default. You can enable it using the CLI command,
no led display off
no led display off
–
You can also configure the local Ethernet ports to a VLAN ID using the interface configuration
command, vlan vlan-id.
command, vlan vlan-id.
•
Support for Cisco Aironet 3700 Series access point
–
This access point is built on 4x4:3(2.4GHz), 4x4:3(5GHz) MIMO technology, with integrated
and external antenna options, and supports 802.11a,b,g,n,ac.
and external antenna options, and supports 802.11a,b,g,n,ac.
–
Supported models are 3700E and 3700I
•
Support for Cisco Aironet 2700 Series access point
–
This access point is built on 3x4:3(2.4GHz), 4x4:3(5GHz) MIMO technology, with integrated
and external antenna options, and supports 802.11a,b,g,n,ac. This access point has both primary
and secondary gigabit Ethernet ports. The primary port is gigabit Ethernet 0 and is the backhaul
port. The primary port can be set as trunk port. The secondary port is gigabit Ethernet 1, and is
the access port. You can configure the secondary port to a VLAN ID using the interface
configuration command bridge multiple-port client-vlan vlan-id
and external antenna options, and supports 802.11a,b,g,n,ac. This access point has both primary
and secondary gigabit Ethernet ports. The primary port is gigabit Ethernet 0 and is the backhaul
port. The primary port can be set as trunk port. The secondary port is gigabit Ethernet 1, and is
the access port. You can configure the secondary port to a VLAN ID using the interface
configuration command bridge multiple-port client-vlan vlan-id
–
Supported models are 2700E and 2700I
•
Support for Cisco Aironet 1700 Series access point
–
This access point is built on 3x3:2(2.4GHz), 3x3:2(5GHz) MIMO technology, and comes with
integrated antennas, and supports 802.11a,b,g,n,ac. This access point has both primary and
secondary gigabit Ethernet ports. The primary port is gigabit Ethernet 0 and is the backhaul
integrated antennas, and supports 802.11a,b,g,n,ac. This access point has both primary and
secondary gigabit Ethernet ports. The primary port is gigabit Ethernet 0 and is the backhaul