Cisco Cisco Prime Optical 10.3 Guía Del Desarrollador
Cisco Prime Optical 10.3 GateWay/CORBA Programmer Reference Guide
60
2.2.7.2.2
Linear-Card Mode
You can apply linear-card mode SNC provisioning to all types of Ethernet cards. One end of the
SNC must be an FTP; the other end can be a CTP on any OC-n port, or an FTP. The FTPs must
use linear-mode naming conventions.
Only single source and single destination are supported for the SNC creation, and the SNC must
be bidirectional.
For E-series and G-series cards, the port number in the FTP name is the number of the front
Ethernet port. For ML-series cards, the port number is the number of the virtual back-end port.
SNC must be an FTP; the other end can be a CTP on any OC-n port, or an FTP. The FTPs must
use linear-mode naming conventions.
Only single source and single destination are supported for the SNC creation, and the SNC must
be bidirectional.
For E-series and G-series cards, the port number in the FTP name is the number of the front
Ethernet port. For ML-series cards, the port number is the number of the virtual back-end port.
2.2.7.2.3
Layer Rates
Prime Optical supports the following layer rates on E-series cards:
• LR_STS1_and_AU3_High_Order_VC3
• LR_STS3c_and_AU4_VC4
• LR_STS6c_and_VC4_2c
• LR_STS12c_and_VC4_4c
Prime Optical supports the following layer rates on G-series cards:
• LR_STS1_and_AU3_High_Order_VC3
• LR_STS3c_and_AU4_VC4
• LR_STS6c_and_VC4_2c
• LR_STS9c_and_VC4_3c
• LR_STS12c_and_VC4_4c
• LR_STS24c_and_VC4_8c
• LR_STS48c_and_VC4_16c
Prime Optical supports the following layer rates on ML-series cards:
• LR_STS1_and_AU3_High_Order_VC3
• LR_STS3c_and_AU4_VC4
• LR_STS6c_and_VC4_2c
• LR_STS9c_and_VC4_3c
• LR_STS12c_and_VC4_4c
• LR_STS24c_and_VC4_8c
Prime Optical supports the following layer rates on FCMR cards:
• LR_STS1_and_AU3_High_Order_VC3
• LR_STS3c_and_AU4_VC4
Prime Optical supports the following layer rate on CE-100T-8 and ML-100T-8 cards:
• LR_STS1_and_AU3_High_Order_VC3
• LR_STS1_and_AU3_High_Order_VC3
• LR_STS3c_and_AU4_VC4
• LR_STS6c_and_VC4_2c
• LR_STS12c_and_VC4_4c
Prime Optical supports the following layer rates on G-series cards:
• LR_STS1_and_AU3_High_Order_VC3
• LR_STS3c_and_AU4_VC4
• LR_STS6c_and_VC4_2c
• LR_STS9c_and_VC4_3c
• LR_STS12c_and_VC4_4c
• LR_STS24c_and_VC4_8c
• LR_STS48c_and_VC4_16c
Prime Optical supports the following layer rates on ML-series cards:
• LR_STS1_and_AU3_High_Order_VC3
• LR_STS3c_and_AU4_VC4
• LR_STS6c_and_VC4_2c
• LR_STS9c_and_VC4_3c
• LR_STS12c_and_VC4_4c
• LR_STS24c_and_VC4_8c
Prime Optical supports the following layer rates on FCMR cards:
• LR_STS1_and_AU3_High_Order_VC3
• LR_STS3c_and_AU4_VC4
Prime Optical supports the following layer rate on CE-100T-8 and ML-100T-8 cards:
• LR_STS1_and_AU3_High_Order_VC3
2.2.7.2.4
SNC Provisioning for ONS 15454 CE-MR-10 Cards
The ONS 15454 CE-MR-10 card implements two different working modes:
• Automatic mode—Available only for ONS 15454 SONET
• Manual (or Exposed) mode—Available for ONS 15454 SONET and ONS 15454 SDH
Automatic mode is similar to the provisioning of existing ML-series cards, where FTPs must be
used for CCAT and VCAT circuit provisioning, and the FTP name is the number of the virtual
back-end port.
Manual mode requires PTPs/CTPs to be specified for the aEnd and zEnd on CCAT circuits, and
for aEnd(s) and zEnd(s) on VCAT member circuits. For VCAT circuit endpoints, FTPs must be
used.
Use one of the following APIs to retrieve available CTPs:
• Automatic mode—Available only for ONS 15454 SONET
• Manual (or Exposed) mode—Available for ONS 15454 SONET and ONS 15454 SDH
Automatic mode is similar to the provisioning of existing ML-series cards, where FTPs must be
used for CCAT and VCAT circuit provisioning, and the FTP name is the number of the virtual
back-end port.
Manual mode requires PTPs/CTPs to be specified for the aEnd and zEnd on CCAT circuits, and
for aEnd(s) and zEnd(s) on VCAT member circuits. For VCAT circuit endpoints, FTPs must be
used.
Use one of the following APIs to retrieve available CTPs: