Cisco Cisco StadiumVision Director Manual De Mantenimiento
© 2012 Cisco Systems, Inc. All rights reserved.
Page 91 of 103
Cisco StadiumVision Director responds with status code 200 (OK), indicating that it
recognizes this URL and is able to process it:
recognizes this URL and is able to process it:
[guest@svd1 httpd]# pwd
/var/log/httpd
[guest@svd1 httpd]# grep 10.10.99.20 access_log
10.10.99.20 - - [08/Sep/2011:06:00:35 -0600] "POST /StadiumVision/dmp_reg
HTTP/1.1" 200 6796 "-" "curl/7.19.6 (mipsel-unknown-linux-gnu) libcurl/7.19.6
OpenSSL/0.9.8o zlib/1.2.3 c-ares/1.7.3"
/var/log/httpd
[guest@svd1 httpd]# grep 10.10.99.20 access_log
10.10.99.20 - - [08/Sep/2011:06:00:35 -0600] "POST /StadiumVision/dmp_reg
HTTP/1.1" 200 6796 "-" "curl/7.19.6 (mipsel-unknown-linux-gnu) libcurl/7.19.6
OpenSSL/0.9.8o zlib/1.2.3 c-ares/1.7.3"
Step 6: Confirm that auto-registration has been enabled. If auto-registration is
disabled then the following error message will appear in the sv_dev_debug.log file.
The same message will also appear in the dashboard under the System tab.
disabled then the following error message will appear in the sv_dev_debug.log file.
The same message will also appear in the dashboard under the System tab.
[guest@svd1 logs]# pwd
/opt/sv/servers/config/logs
[guest@svd1 logs]# egrep -i 'auto registration' sv_dev_debug.log
2011-09-08 06:17:16,000 [HPMThreadPoolExecutor-ThreadPool-system] INFO
com.cisco.sv.tools.common.SvLoggerFactory - Auto registration is disabled.
Discarding registration message from: 10.10.99.20
/opt/sv/servers/config/logs
[guest@svd1 logs]# egrep -i 'auto registration' sv_dev_debug.log
2011-09-08 06:17:16,000 [HPMThreadPoolExecutor-ThreadPool-system] INFO
com.cisco.sv.tools.common.SvLoggerFactory - Auto registration is disabled.
Discarding registration message from: 10.10.99.20
Step 7: Confirm that auto-provisioning has been enabled. If auto-provisioning is not
enabled then the following error message will appear in the sv_dev_debug.log file.
In this case there is no corresponding message posted in the dashboard.
enabled then the following error message will appear in the sv_dev_debug.log file.
In this case there is no corresponding message posted in the dashboard.
[guest@svd1 logs]# pwd
/opt/sv/servers/config/logs
2011-09-08 06:26:55,574 [HPMThreadPoolExecutor-ThreadPool-system] INFO
com.cisco.sv.hpm.endpoint.dmp.CompositeCommand - Auto provision is disabled,
device com.cisco.sv.hpm.endpoint:type=DMP,id=181 ,name=181-ip-10-10-99-20-mac-00-
0f-44-01-57-b7 must be manually provisioned by using the 'Provision DMP' command
/opt/sv/servers/config/logs
2011-09-08 06:26:55,574 [HPMThreadPoolExecutor-ThreadPool-system] INFO
com.cisco.sv.hpm.endpoint.dmp.CompositeCommand - Auto provision is disabled,
device com.cisco.sv.hpm.endpoint:type=DMP,id=181 ,name=181-ip-10-10-99-20-mac-00-
0f-44-01-57-b7 must be manually provisioned by using the 'Provision DMP' command
Step 8: Make sure that the DMP trying to auto-register is not already present in the
Cisco StadiumVision Director database. If it is present then Cisco StadiumVision
Director will assume this is an existing DMP that is simply rebooting and hence
ignore the auto-registration request. The following error messages will appear in the
sv_dev_debug.log file. The same message will also appear in the dashboard under
the System tab, but not under the Console tab as you might expect since the DMP
in question is listed in the dashboard. To correct this situation either delete the DMP
from the database or change its state to ‘Not Ready’.
Cisco StadiumVision Director database. If it is present then Cisco StadiumVision
Director will assume this is an existing DMP that is simply rebooting and hence
ignore the auto-registration request. The following error messages will appear in the
sv_dev_debug.log file. The same message will also appear in the dashboard under
the System tab, but not under the Console tab as you might expect since the DMP
in question is listed in the dashboard. To correct this situation either delete the DMP
from the database or change its state to ‘Not Ready’.
[guest@svd1 logs]$ egrep -i 'NEW|10.10.99.30' sv_dev_debug.log
2011-10-20 22:01:06,847 [TP-Processor10] 9968bfae INFO
com.cisco.sv.autoregister.DMPAutoRegister - Received DMP auto register message
from: 10.10.99.30 message: 00:0f:44:01:57:b7
com.cisco.sv.autoregister.DMPAutoRegister - Received DMP auto register message
from: 10.10.99.30 message: 00:0f:44:01:57:b7
2011-10-20 22:01:22,204 [HPMThreadPoolExecutor-ThreadPool-system] INFO
com.cisco.sv.tools.common.SvLoggerFactory - Device 'Boulder-A' is not 'NEW',
ignoring register message
com.cisco.sv.tools.common.SvLoggerFactory - Device 'Boulder-A' is not 'NEW',
ignoring register message