Cisco Cisco 1 GHz GainMaker Amplifier Hoja De Datos

®

 

5

 

 

The GainMaker Ordering Matrix provides ordering information for configured amplifier modules or stations.  This page 
contains ordering information for required and optional accessories that are not included as part of a configured amplifier 
module or station.  Consult your account representative or customer service representative for ordering assistance. 

 

Required Accessories 

Plug-in Pads (attenuators) - Available in 0.5 dB steps from 0 to 20.5 dB 
• 

1 required for forward input  

• 

1 required for AGC, if applicable* 

• 

4 required for reverse (3 input, 1 output) 

*To determine AGC pad value, subtract 26 dB from the design value main port RF output level at the AGC pilot 
frequency (applies to UBT only) 

589693 (0 dB) 

sequentially thru 

589734 (20.5 dB) 

Plug-in Forward Equalizer - Available in 1.5 dB steps from 0 to 30 dB at 1002 MHz  
• 

1 required for forward input  

4007228 (0 dB) 

sequentially thru 

4007248 (30 dB) 

 

Plug-in Reverse Equalizer – Available in 1 dB steps from 0 to 12 dB at 65 MHz 

• 

1 required for reverse output - unless design value is 0 dB (0 dB EQ is provided) 

712719 (0 dB) and 

589736 (1 dB) 

sequentially thru 

589747 (12 dB) 

 

 

230 V AC Crowbar Surge Protector (plug-in, one per station) 

715973 

Plug-in Inverse Equalizer.  Simulates cable equivalent tilts (creates tilt opposite that of equalizers).  Use in place of 
forward input EQ as needed to maintain proper output tilt in short spaced locations.  Available in approx. 1.6 dB 
“cable equivalent” steps from 1.6 to 16.2 dB.  

4007486 (1.6 dB) 

sequentially thru 

4007495 (16.2 dB) 

Long Reach Test Point Adapter 

562580 

Status Monitoring Transponder –   * see GainMaker Status Monitoring Transponder Data Sheet 

* 

GainMaker System Amplifier Housing – 1 required Housing includes housing base, lid, wiring harness, and 24 V 
power supply # 734771.  All Housings have 15 amp capacity. 

• 

Uncoated 4 port housing without external test point access 

714027 

• 

Coated 4 port housing without external test point access 

714026 

• 

Uncoated 4 port housing with external test point access 

714025 

• 

Coated 4 port housing with external test point access 

714024 

GainMaker System Amplifier Housing Upgrade Kit - 1 required if upgrading an existing SA II, II+, or III housing to 
allow use of GainMaker System Amplifier modules.  Includes a GainMaker System Amplifier housing lid, wiring 
harness, and 24 V power supply # 734771. 

 

• 

Uncoated 4 port housing lid without external test point access 

714023 

• 

Coated 4 port housing lid without external test point access 

714022 

• 

Uncoated 4 port housing lid with external test point access 

714021 

• 

Coated 4 port housing lid with external test point access 

714020 

Seizure Upgrade Kit – 1 required if upgrading an existing SAII or SAII+ housing base to allow use of GainMaker 
System Amplifier Modules.  Includes high current (15 amp) rated seizure screws and anvils. 

548775 

 
 
 
 
 
 
 
 
 

 

Scientific-Atlanta and the Scientific-Atlanta logo are registered trademarks of Scientific-Atlanta, Inc. 
ROSA is a trademark of Scientific-Atlanta Europe NV. 
Specifications and product availability are subject to change without notice. 
© 2006 Scientific-Atlanta, Inc. All rights reserved. 
 
Scientific-Atlanta, Inc. 
1-800-722-2009 or 770-236-6900 

www.scientificatlanta.com

 

Part Number 7006951 Rev B

 

November 2006