Cisco Cisco 1 GHz GainMaker Amplifier Guía De Instalación
Index
GainMaker Line Extender Block Diagram • 10
GainMaker Line Extender Characteristics • 3
GHz • 120
GainMaker Line Extender Characteristics • 3
GHz • 120
H
Hertz • 120
Housing Dimensions • 13
Housing Dimensions • 13
I
I/O • 120
Illustrations • 8
in-lb • 120
Input and Output Ports • 4
Installation and Configuration • 11
Installing Accessories • 28
Installing the Amplifier Module • 32
Installing the Housing • 25
Installing the Power Supply • 20
Introduction • 1
Illustrations • 8
in-lb • 120
Input and Output Ports • 4
Installation and Configuration • 11
Installing Accessories • 28
Installing the Amplifier Module • 32
Installing the Housing • 25
Installing the Power Supply • 20
Introduction • 1
L
LE • 121
LED • 121
Line Extender Accessories • 9
Line Extender Test Points • 8
Low or Degraded Forward RF Signal • 90
Low or Degraded Forward RF Signal
LED • 121
Line Extender Accessories • 9
Line Extender Test Points • 8
Low or Degraded Forward RF Signal • 90
Low or Degraded Forward RF Signal
Troubleshooting Table • 90
Low or Degraded Reverse RF Signal • 93
Low or Degraded Reverse RF Signal
Low or Degraded Reverse RF Signal
Troubleshooting Table • 93
M
Manual Backoff Chart • 49
Mbps • 121
MHz • 121
Miscellaneous Accessories • 7
Module and Housing Compatibility • 13
Mbps • 121
MHz • 121
Miscellaneous Accessories • 7
Module and Housing Compatibility • 13
N
N-cm • 121
Nm • 121
No AC Power • 85
No AC Power Troubleshooting Table • 85
No DC Power • 87
No DC Power Troubleshooting Table • 88
No Forward RF Signal • 89
No Forward RF Signal Troubleshooting Table • 89
No Reverse RF Signal • 92
No Reverse RF Signal Troubleshooting Table • 92
Nm • 121
No AC Power • 85
No AC Power Troubleshooting Table • 85
No DC Power • 87
No DC Power Troubleshooting Table • 88
No Forward RF Signal • 89
No Forward RF Signal Troubleshooting Table • 89
No Reverse RF Signal • 92
No Reverse RF Signal Troubleshooting Table • 92
O
Obtaining an RMA Number and Shipping Address
• 98
Obtaining Product Support • 96
Opening the Node Housing • 15
Opening the Node Housing • 15
P
Packing and Shipping the Product • 102
Power Supply • 4
Preparing for Forward Path Balancing • 42
PWB • 121
Power Supply • 4
Preparing for Forward Path Balancing • 42
PWB • 121
R
Removing and Installing AC Shunt Power
Directors • 37
Removing the Amplifier Module from the Housing
• 35
Required Tools • 12
Return Product for Repair • 98
Reverse Cable Equalizer Charts • 110
Reverse Cable Equalizer Part Numbers • 117
Reverse Path Balancing, About • 77
RF • 121
RMA • 121
RX • 121
Return Product for Repair • 98
Reverse Cable Equalizer Charts • 110
Reverse Cable Equalizer Part Numbers • 117
Reverse Path Balancing, About • 77
RF • 121
RMA • 121
RX • 121
S
S/N or SNR • 121
SA • 122
Specifications • 118
Support Telephone Numbers • 96
Switch S1 Positions for AGC Stations • 42
Switch S1 Positions for Manual Stations • 44
Switch S1 Positions for Thermal Stations • 44
SA • 122
Specifications • 118
Support Telephone Numbers • 96
Switch S1 Positions for AGC Stations • 42
Switch S1 Positions for Manual Stations • 44
Switch S1 Positions for Thermal Stations • 44
T
Test Points • 4
To Align the AGC Module • 54, 61
To Calculate the Proper RF Signal Level • 79
To Close the Node Housing • 39
To Complete Reverse Path Balancing • 81
To Connect the Coaxial Cable Pin Connector to the
To Align the AGC Module • 54, 61
To Calculate the Proper RF Signal Level • 79
To Close the Node Housing • 39
To Complete Reverse Path Balancing • 81
To Connect the Coaxial Cable Pin Connector to the
Node Housing • 24
To Determine the Output Tilt • 51, 58, 66, 69, 72
To Install a Trim Network • 75
To Install Attenuator Pads • 28
To Install Equalizers • 29
To Install the Amplifier Module • 32
To Install the Housing in a Pedestal • 26
To Install the Housing on a Strand (Aerial) • 25
To Install the New Housing Lid • 18
To Install the New Housing Seizures • 16
To Install the Power Supply Module • 20
To Install a Trim Network • 75
To Install Attenuator Pads • 28
To Install Equalizers • 29
To Install the Amplifier Module • 32
To Install the Housing in a Pedestal • 26
To Install the Housing on a Strand (Aerial) • 25
To Install the New Housing Lid • 18
To Install the New Housing Seizures • 16
To Install the Power Supply Module • 20
114
OL-31155-01