ASUS p3cd Manual De Usuario
22
ASUS P3C-D User’s Manual
3. HARDWARE SETUP
System Memory
3. H/W SETUP
3.5 System Memory
NOTE: No hardware or BIOS setup is required after adding or removing memory.
This motherboard has three Rambus Inline Memory Module (RIMM) sockets. The
first two sockets (see Important notes for details) support Direct RDRAMs (both
ECC and non-ECC are supported) in 64, 96, 128, 192, 256, and 512MB densities for
a maximum of 1GB.
With the optional ASUS DR1 DIMM Riser, unbuffered Synchronous Dynamic Ran-
dom Access Memory (SDRAM, 3.3V power level) in 64, 128, 256, or 512MB densi-
ties with Serial Presence Detect (SPD) can be used on the third socket for a maxi-
mum of 1GB.
The chipset’s Error Checking and Correction (ECC) feature is available only when
using RDRAMs. ECC feature is not available when using SDRAM with an ASUS
DIMM Riser (ECC memory modules may still be used, but the ECC function will
not be available).
For memory speed setup, see 4.4.1 CHIP Configuration.
first two sockets (see Important notes for details) support Direct RDRAMs (both
ECC and non-ECC are supported) in 64, 96, 128, 192, 256, and 512MB densities for
a maximum of 1GB.
With the optional ASUS DR1 DIMM Riser, unbuffered Synchronous Dynamic Ran-
dom Access Memory (SDRAM, 3.3V power level) in 64, 128, 256, or 512MB densi-
ties with Serial Presence Detect (SPD) can be used on the third socket for a maxi-
mum of 1GB.
The chipset’s Error Checking and Correction (ECC) feature is available only when
using RDRAMs. ECC feature is not available when using SDRAM with an ASUS
DIMM Riser (ECC memory modules may still be used, but the ECC function will
not be available).
For memory speed setup, see 4.4.1 CHIP Configuration.
IMPORTANT
General
1. DO NOT attempt to mix RDRAMs with an SDRAM+Riser or vice versa.
1. DO NOT attempt to mix RDRAMs with an SDRAM+Riser or vice versa.
RDRAM
1. If more than one socket will be populated with RDRAMs, RIMM0 must be
1. If more than one socket will be populated with RDRAMs, RIMM0 must be
populated first and then RIMM1. The bundled ASUS CTRIMM must be used
in RIMM2. If only one socket will be populated, RIMM0 must be populated
with RDRAM, RIMM1 with the CTRIMM, and RIMM2 with the C-RIMM.
See table for an overview.
in RIMM2. If only one socket will be populated, RIMM0 must be populated
with RDRAM, RIMM1 with the CTRIMM, and RIMM2 with the C-RIMM.
See table for an overview.
SDRAM
1. To use SDRAM with this motherboard, an ASUS DR1 DIMM Riser must be
1. To use SDRAM with this motherboard, an ASUS DR1 DIMM Riser must be
installed as an interface (see 3.5.2 Installing Memory Using the ASUS DR1 DIMM
Riser). The riser must (and can only) be inserted into RIMM2, with the bundled
C-RIMMs inserted into RIMM0 and RIMM1. See table for an overview.
Riser). The riser must (and can only) be inserted into RIMM2, with the bundled
C-RIMMs inserted into RIMM0 and RIMM1. See table for an overview.
2. When populating both DIMM sockets in the riser, the module density on J1M2
must be greater than the one on J1M1.
3. This motherboard’s chipset only supports 64Mbit and 128Mbit SDRAMs (see
SDRAM Configurations). 32Mx4 128 Mbit support is for registered DIMMs
only. 4Mx16 64 Mbit support is for unbufferred DIMMs only.
only. 4Mx16 64 Mbit support is for unbufferred DIMMs only.
C-RIMM/CTRIMM
1. Depending on your configuration, a C-RIMM (Continuity RIMM) or CTRIMM,
1. Depending on your configuration, a C-RIMM (Continuity RIMM) or CTRIMM,
or both must be used to complete the sockets that are not populated by either
RDRAMs or an ASUS DIMM Riser (when using SDRAM). C-RIMM is neces-
sary to avoid breaking the signal lines, which are a serial connection in a Rambus
interface, such as used in this motherboard. CTRIMM is used to minimize sig-
nal reflections or control the impedance at the end of the signal line. Both C-
RIMM and CTRIMM assure the electrical integrity of a Rambus interface.
RDRAMs or an ASUS DIMM Riser (when using SDRAM). C-RIMM is neces-
sary to avoid breaking the signal lines, which are a serial connection in a Rambus
interface, such as used in this motherboard. CTRIMM is used to minimize sig-
nal reflections or control the impedance at the end of the signal line. Both C-
RIMM and CTRIMM assure the electrical integrity of a Rambus interface.