Canon mf3220, mf3228, mf3240 Manuales De Servicio

5-2

0030

Can't receive any signal within 6 sec. At phase D.

0031

Received incorrect signal at phase D (not EOP, MPS, EOM, DCN, PPS_Q, PPS_Q,etc)

0032

Can't receive carrier within 6 sec after sending MCF or RTP, RTN signal

0033

Received DCN signal at ohase D within pages (not last page).

0039

In non_ECM mode, when machine alredy received the data dosen't receive 13.1 seconds

001F

Can't detect any G3 signal within 35 sec after sending DTC signal

003F

Remote side TSI not define in machine one touch or speed dial directory

0040

Can't receive carrier within 6 sec. after sending CTR.

0041

Can't receive carrier within 6 sec. after sending PPR.

0042

Can't receive correct signal after sending RNR signal

0043

Receive incorrect signal at phase D in ECM mode.

0044

Can't receive carrier/FSK signal within 6 sec. After sending MCF. ln ECM mode.

0047

Can't receive correct signal or DCN received after sending ERR signal.

0048

Can't receive correct signal after receive PPS_PRI_Q

004B

Can't detect correct FSK signal even through detected FSK tone within 6 sec.

004C

Handshake fail during re-train or between page in V34 Rx.

004E

Receive DCN signal after sending DIS in V.34.

004F

Remote side disconnected after sending ANSam in V.8 phase.

0050

Can't receive any correct signal after detected CJ signal in V.8 phase.

0051

Can't receive phase 3 signal after phase 2 within 20 seconds in V.34.

0053

Modem disconnect after phase 4 in V.34.

0054

Remote side disconnect after phase 4 in V.8

0055

Receive incorrect signal after sending DIS signal in V.34

0056

Modem disconnect after sending CFR in V.34

0058

Can't detect image signal within 6 sec after modem enter to primary phase in V.34

005A

Modem cannot  detect any correct ECM frame with 3 minutes in phase C.

005B

Modem can't detect control channel with 12 sec in phase C

005C

Detect busy tone within control channel after phase C.

005D

Modem can't detect any correct ECM frame with 12 sec in phase C.

005E

Can't detect control channel signal  after received RCP frame within 6 sec

005F

Can't detect silence after sending JM signal for polling TX function.

0060

There are no any bullietin files to be polled in V.34.

0061

Machine cannot detect V.21 or V.8 signal with 35 sec.

0062

Modem disconnect in phase D after our side sending out flags sequence in control channel.

0063

Can't receive any flag sequence in control channel within 25 sec in phase D.

0064

Can't detect any control channel signal in phase D within 60 sec even through energy still on the 
line.

0065

Can't detect any control channel signal within 60 sec after detect sillence in phase D.

0066

Can't receive T.30 signal or carrier after sending CFR in V.34.

0069

Capability no match paper size after received is DCS signal.

0070

User press stop key within receiving.

0071

Memory full within receiving.

0080

Can't detect any G3 signal within 35 sec. specified by ITU-T in phase B.

0081

Received DTC signal in transmission phase.

0082

Transmitting unit receives a signal other than DIS or DTC. And DCN in phase B.

0083

Detected FSK signal, but Can't receive any signal within 35 sec.

0084

Detect DCN signal in phase B.

0085

Transmitting unit sending DCS 3 times consecutively, but each time responds with DIS/DTC

0086

Detected responds signal other than DTC,DIS,FTT,DCN or CFR after sending DCS.

0087

Training attempt has failed because speed unit can't adjust to low lower speed.

0088

Received DCN signal after sending out DCS signal

008B

Receivers  protcol of DIS is received, but it is not compatible with our machine.

008C

Remote side or our side not support capability.

008D

Receivers protocol of DIS is received, but remote side can't receive document temporary, may 
because by run out of paper or other reason.

008F

Modem not ready to received V.34 data within 6 sec after received CFR signal.

0090

Called side document not ready for our polling.

0091

Can't receive any commabd after send DCN signal 3 times consecutively

0093

Received DCN signal after sending out DCN signal

0094

Time out during transmit ECM frame or RCP command.

0095

Wrong ID number

0096

SUBADDRESS/PASSWORD capability not match in polling Rx mode.

009A

Can't detect any signal after sending CI signal.

009D

Remote side hang up before V.34 modem enter phase 2 state in V.34 polling Rx.

009E

Manual Tx over 15 minutes whin in phase C by non-ECM mode.

00A0

User stop or cancel transmission job.

00A1

Document JAM within transmission