Samsung SCX-4321 Manual De Usuario

vii

The Ringer Equivalence Number and FCC Registration Number for this 
machine may be found on the label located on the bottom or rear of the 

machine. In some instances you may need to provide these numbers to the 
telephone company.
The Ringer Equivalence Number (REN) is a measure of the electrical load 

placed on the telephone line, and is useful for determining whether you have 
“overloaded” the line. Installing several types of equipment on the same 
telephone line may result in problems making and receiving telephone calls, 

especially ringing when your line is called. The sum of all Ringer Equivalence 
Numbers of the equipment on your telephone line should be less than five in 
order to assure proper service from the telephone company. In some cases, 

a sum of five may not be usable on your line. If any of your telephone 
equipment is not operating properly, you should immediately remove it from 
your telephone line, as it may cause harm to the telephone network.

WARNING:
FCC Regulations state that changes or modifications to this equipment not 
expressly approved by the manufacturer could void the user’s authority to 

operate this equipment. In the event that terminal equipment causes harm 
to the telephone network, the telephone company should notify the customer 
that service may be stopped. However, where prior notice is impractical, the 

company may temporarily cease service, providing that they:
a) promptly notify the customer.
b) give the customer an opportunity to correct the equipment problem.
c) inform the customer of the right to bring a complaint to the Federal 
Communication Commission pursuant to procedures set out in FCC Rules and 
Regulations Subpart E of Part 68.

• Your machine is not designed to be connected to a digital PBX system.
• If you intend to use a computer modem or fax modem on the same phone 

line as your machine, you may experience transmission and reception 

problems with all the equipment. It is recommended that no other 
equipment, except for a regular telephone, share the line with your 
machine.

• If your area experiences a high incidence of lightning or power surges, we 

recommend that you install surge protectors for both the power and the 

telephone lines. Surge protectors can be purchased from your dealer or 
telephone and electronic specialty stores.

• When programming emergency numbers and/or making test calls to 

emergency numbers, use a non-emergency number to advise the 
emergency service dispatcher of your intentions. The dispatcher will give 

you further instructions on how to actually test the emergency number.

• This machine may not be used on coin service or party lines.
• This machine provides magnetic coupling to hearing aids.
• You may safely connect this equipment to the telephone network by 

means of a standard modular jack, USOC RJ-11C.

The CE marking applied to this product symbolizes Samsung 

Electronics Co., Ltd. Declaration of Conformity with the 
following applicable 93/68/EEC Directives of the European 
Union as of the dates indicated:

: Council Directive 73/23/EEC Approximation of the laws 

of the member states related to low voltage equipment.

: Council Directive 89/336/EEC (92/31/EEC), 

approximation of the laws of the Member States related to electromagnetic 
compatibility.

: Council Directive 1999/5/EC on radio equipment and 

telecommunications terminal equipment and the mutual recognition of their 
conformity.
A full declaration, defining the relevant Directives and referenced standards 
can be obtained from your Samsung Electronics Co., Ltd. representative.

This Samsung product has been self-certified by Samsung for pan-European 
single terminal connection to the analogue public switched telephone 
network (PSTN) in accordance with Directive 1999/5/EC. The product has 

been designed to work with the national PSTNs and compatible PBXs of the 
European countries:
In the event of problems, you should contact the Euro QA Lab of Samsung 

Electronics Co., Ltd. in the first instance.
The product has been tested against TBR21. To assist in the use and 
application of terminal equipment which complies with this standard, the 

European Telecommunication Standards Institute (ETSI) has issued an 
advisory document (EG 201 121) which contains notes and additional 
requirements to ensure network compatibility of TBR21 terminals. The 

product has been designed against, and is fully compliant with, all of the 
relevant advisory notes contained in this document. 

The mains lead for this machine is fitted with a standard (BS 1363) 13 amp 

plug and has a 13 amp fuse. When you change or examine the fuse, you 
must re-fit the correct 13 amp fuse. You then need to replace the fuse cover. 
If you have lost the fuse cover, do not use the plug until you have another 

fuse cover. 
Please contact the people from you purchased the machine.
The 13 amp plug is the most widely used type in the UK and should be 

suitable. However, some buildings (mainly old ones) do not have normal 13 
amp plug sockets. You need to buy a suitable plug adaptor. Do not remove 
the moulded plug.