Samsung wt80s1(p) Manual De Usuario
1 After rinsing you can select this
course for more effective rinse
(Don't just select this course
for rinse.) Load the laundry
evenly into the spin basket.
(Don't just select this course
for rinse.) Load the laundry
evenly into the spin basket.
2 Set the WATER SELECTOR
KNOB to SPIN and
CYCLE SELECTOR
KNOB to ‘DRAIN’.
CYCLE SELECTOR
KNOB to ‘DRAIN’.
3 Supply water for about 1 minute.
Adjust the water flow to prevent
overflow from the wash tub.
overflow from the wash tub.
4 After completing the water supply,
cover the laundry with
safety cover and close
the inner lid.
safety cover and close
the inner lid.
5 Close the spin dryer lid.
6 Set the SPIN DRY
TIMER 2~3 minutes.
Leave some space of
at least 15cm between the washing machine
and the wall.
and the wall.
Place the washing machine on a sturdy flat surface.
If the washing machine is placed on an uneven
or weak surface, noise or vibration may occur.
(Allowable is 2˚)
or weak surface, noise or vibration may occur.
(Allowable is 2˚)
Never install the washing machine near water.
Do not place the washing machine in steamy
room or where the washing machine is directly
exposed to rain.
Moisture may damage electrical insulation and
cause an electrical shock to occur.
room or where the washing machine is directly
exposed to rain.
Moisture may damage electrical insulation and
cause an electrical shock to occur.
Avoid direct sunlight or heating devices.
As plastic and electrical components are
affected by direct heat, never place the washing
machine near heaters, boilers, etc., or under direct
sunlight.
affected by direct heat, never place the washing
machine near heaters, boilers, etc., or under direct
sunlight.
Install the drain hose
about 70~80cm above
the ground for pump model.
about 70~80cm above
the ground for pump model.
MOUNTING THE LEGS
Lay down the washer with its back facing
downward. Insert four legs into the leg mounting
sections of the base corners of the main body.
Insert the claw of the
leg with the square
hole of the leg
mounting section,
and push the leg in
the arrow direction
as shown in the
figure until it clicks.
downward. Insert four legs into the leg mounting
sections of the base corners of the main body.
Insert the claw of the
leg with the square
hole of the leg
mounting section,
and push the leg in
the arrow direction
as shown in the
figure until it clicks.
After attaching the connector ring(a), insert the
drain hose(b) in the draining direction.
drain hose(b) in the draining direction.
CONNECTING THE DRAIN HOSE
1. Before connecting the drain hose, remove
1. Before connecting the drain hose, remove
the cover (a) from the drain hole.
2. After pressing the joint ring (b), insert the
drain hose(c) to drain direction.
CHANGING THE POSITION OF THE
DRAIN HOSE
Before attempting to change the position of the
drain hose, disconnect the plug from the outlet.
1. Route the drain hose inside the machine.
2.Take out the drain hose from the opposite hole
DRAIN HOSE
Before attempting to change the position of the
drain hose, disconnect the plug from the outlet.
1. Route the drain hose inside the machine.
2.Take out the drain hose from the opposite hole
and insert the drain hose into the hose holder.
WATER SELECTOR
Wash
Spin
Drain
CYCLE SELECTOR
70~80cm
Claw
Square
hole
Bottom face of
main body
Leg
1
2
inner lid
safety
cover
cover
0
3
1
4
2
5
SPIN DRY TIMER
INSTALLATION
ADDITIONAL RINSE
LOCATION
CONNECTING THE DRAIN HOSE
a
b
(In case of pump
drained washer)
drained washer)
(C)
(b)
(C)
(b)
(a)
2
1
Hose holder
4