Sony 5500 Manual De Usuario
60
4-3 TC Menu
C
h
h
ap
te
te
r 4
M
e
nu
Se
tt
tt
in
g
s
To pause the current time
Press the [F4] (TIMER HOLD) button.
The time is paused only while the button is held down.
The time is paused only while the button is held down.
4-3-2 Setting the Time Code Reader
(TCR SEL)
(TCR SEL)
Press the [F5] (TCR SEL) button to select the time code to
be read by the time code reader during playback.
VITC: Reads VITC.
auto: Reads VITC when the playback speed is ±1/2 times
be read by the time code reader during playback.
VITC: Reads VITC.
auto: Reads VITC when the playback speed is ±1/2 times
normal speed or less, and LTC when it is greater than
±1/2 times normal speed.
±1/2 times normal speed.
LTC: Reads LTC.
Depending on the time code recorded on a tape, VITC or
LTC appears on the display.
Depending on the time code recorded on a tape, VITC or
LTC appears on the display.
Time codes that are read by the time code reader or played
back are output from the TIME CODE OUT connector.
back are output from the TIME CODE OUT connector.
4-3-3 Setting the Time Code
Generator (TCG SOURCE/MODE)
Generator (TCG SOURCE/MODE)
There are two ways to record time codes on the VTR. One
way is to record the output of the VTR’s internal time code
generator. The other is to directly record time codes that
are input from an external time code generator.
The output from the internal time code generator can either
be set to a specified initial value, or synchronized with an
external time code generator.
The internal time code generator time code settings are
made with the [F6] (REGENE SOURCE)/[F7] (TCG
MODE) buttons. Menu selections and settings are shown
in the following table.
way is to record the output of the VTR’s internal time code
generator. The other is to directly record time codes that
are input from an external time code generator.
The output from the internal time code generator can either
be set to a specified initial value, or synchronized with an
external time code generator.
The internal time code generator time code settings are
made with the [F6] (REGENE SOURCE)/[F7] (TCG
MODE) buttons. Menu selections and settings are shown
in the following table.
Regenerated signals are selected using the VTR SETUP
menu item 608 “TCG/UBG REGENE MODE setting”.
menu item 608 “TCG/UBG REGENE MODE setting”.
To check the running of the internal time code
generator
Press the INPUT CHECK button.
generator
Press the INPUT CHECK button.
4-3-4 Selecting the Time Code
Running Mode (RUN MODE)
Running Mode (RUN MODE)
Press the [F8] (RUN MODE) button to select the time code
running mode.
free: The time code advances when the power is on
running mode.
free: The time code advances when the power is on
regardless of the VTR’s operation mode.
rec: The time code advances only during recording.
Note
TCG
[F6]
(REGENE
SOURCE)
(REGENE
SOURCE)
[F7] (TCG
MODE)
MODE)
Setting
Internal TCG
(Preset)
(Preset)
prst
Time codes
can be freely
set using the
internal time
code generator
can be freely
set using the
internal time
code generator
Internal TCG
(Regenerate)
(Regenerate)
int-LTC
regene
Lock to the
time data
recorded on
the time code
tracks
time data
recorded on
the time code
tracks
int-VITC
regene
Lock to the
time data
recorded as
video AUX data
on the tape
time data
recorded as
video AUX data
on the tape
ext-LTC
regene
Lock to the
time data on
the TIME
CODE IN
connector
time data on
the TIME
CODE IN
connector
SDI-V
regene
Lock to the
VITC time data
in the video
signal from the
HD SDI INPUT
A/B connector
VITC time data
in the video
signal from the
HD SDI INPUT
A/B connector
SDI-L
regene
Lock to the LTC
time data in the
video signal
from the HD
SDI INPUT A/B
connector
time data in the
video signal
from the HD
SDI INPUT A/B
connector
auto
“int-LTC/
regene” is set
in assemble or
insert mode
and “prst” is set
in other modes
regene” is set
in assemble or
insert mode
and “prst” is set
in other modes
Note
Menu