Sony MKS-2010 Manual De Usuario
158
Basic Settings
Ch
a
a
p
te
r
9
Sys
te
m
Set
tin
gs
gs
To use the rightmost buttons in cross-point
button rows as [SHIFT] buttons (shift mode
selection)
By a XPT Assign menu setting, you can use the rightmost
buttons on cross-point button rows (the 12th buttons on
1M/E or 1.5M/E panels, or the 20th buttons on 1.5M/E
wide panels) as [SHIFT] buttons, which switch between
cross-point button numbers.
In the XPT Assign menu, press [Shift Mode] to display a
popup window, and select a setting other than Off.
Hold: Shift-side cross-point buttons are enabled as long as
button rows as [SHIFT] buttons (shift mode
selection)
By a XPT Assign menu setting, you can use the rightmost
buttons on cross-point button rows (the 12th buttons on
1M/E or 1.5M/E panels, or the 20th buttons on 1.5M/E
wide panels) as [SHIFT] buttons, which switch between
cross-point button numbers.
In the XPT Assign menu, press [Shift Mode] to display a
popup window, and select a setting other than Off.
Hold: Shift-side cross-point buttons are enabled as long as
the rightmost button is held down.
Lock: Shift-side cross-point buttons are enabled as long as
the rightmost button is on.
Off: Do not use the rightmost buttons as [SHIFT] buttons.
Note
The dedicated [SHIFT] button above the cross-point
button rows is disabled when you select a setting other than
Off.
button rows is disabled when you select a setting other than
Off.
Signals assigned to cross-point buttons
You can assign two signals, the video signal and key
signal, as a pair to each cross-point button number. With
this unit you can register a maximum of 40 pairs of video
and key signals. For each pair the assigned number is
referred to as a pair number. The signal assignment to
signal, as a pair to each cross-point button number. With
this unit you can register a maximum of 40 pairs of video
and key signals. For each pair the assigned number is
referred to as a pair number. The signal assignment to
cross-point buttons is done by assigning pair numbers to
cross-point button numbers.
cross-point button numbers.
For the operation of combining a video signal and key
signal, see “Creating a pair from a video signal and key
signal” (page 159).
signal, see “Creating a pair from a video signal and key
signal” (page 159).
Assigning signals to cross-point buttons
To carry out the assignment of a video signal and key
signal pair to a cross-point button, use the Xpt Assign
menu.
signal pair to a cross-point button, use the Xpt Assign
menu.
1
From the top menu, select Setup/Diag >Operation
>Xpt Assign.
>Xpt Assign.
The Xpt Assign menu appears.
c)
[SHIFT] Off
a)
12
(SHIFT)
1
13
(12)
d)
:
:
[SHIFT] On
b)
24
(SHIFT)
11
23
(22)
10
22
(21)
9
21
(20)
8
20
(19)
7
19
(18)
6
18
(17)
5
17
(16)
4
16
(15)
3
15
(14)
2
14
(13)
AUX
AUX1
SRC
BUS
BUS
KEY
XP/KY
HOLD
SHIFT
M/E
PGM
COLOR
BKGD
AUX2
AUX3
AUX4
EDIT
PVW
PVW
UTIL
KEY1
KEY2
DSK1
DSK2
CCR1
CCR2
FRAME
MEM
AUX DELEGATION
BLACK
Cross-point button numbers in the AUX bus control block
XPT/KY HOLD button
Dedicated SHIFT button
a) For a 1.5 M/E wide panel, button numbers: 1 to 20
b) For a 1.5 M/E wide panel, button numbers: 21 to 40
c) The signal assignment to these buttons cannot be changed.
d) The numbers in parentheses are the button numbers when shift mode is on (set to something other than Off).