Panasonic cq-d5501u Manual De Usuario
51
50
E
N
N
G
L
I
S
H
H
CQ-D5501U
50
49
E
N
N
G
L
I
S
H
H
CQ-D5501U
Wiring
Connection with the CD Changer and the Overhead Monitor (CY-VH9300U)
Connection with CD changer and the overhead monitor (option, CX-DP880, CY-VH9300U).
Note:
¡Refer to the operating instructions for the connected devices, in addition.
Note:
¡Refer to the operating instructions for the connected devices, in addition.
VIDEO-CONT
ACC
BATTERY 15A
FRONT SP
REAR SP
PARKING BRAKE
+
-
+
-
VIDEO-OUT
CH/AUX-IN
+
-
+
-
1
3
2
VIDEO CONT
VTR1 – IN
Ground Lead
To a clean, bare metallic part of the car
chassis.
To a clean, bare metallic part of the car
chassis.
Parking Brake Lead
(Blue/yellow stripe)
Be sure to wire the parking brake
for safety and preventing accident.
(Blue/yellow stripe)
Be sure to wire the parking brake
for safety and preventing accident.
Power Lead
To ACC power, + 12 V DC
To ACC power, + 12 V DC
Video Control Lead
(Green/yellow stripe)
(Green/yellow stripe)
Battery Lead
To the car battery, continuous + 12 V DC
To the car battery, continuous + 12 V DC
(Black)
(Yellow)
(Red)
CQ-D5501U
DVD Player/Receiver
CX-DP880
(Option)
CD Changer Unit
Antenna Cable
Antenna
Power Connector
Ground Lead
To a clean, bare metallic
part of the car chassis.
To a clean, bare metallic
part of the car chassis.
Extension Cord
(DIN/BATT/RCA/GND)
(DIN/BATT/RCA/GND)
(R)(Red)
(L)(White)
CH/AUX-IN
RCA Cord
VIDEO-OUT (Yellow)
RCA Cord
VIDEO-IN
(Yellow)
(Yellow)
Not used
CY-VH9300U (Option)
Over Head Monitor
Over Head Monitor
Battery Lead
To the car battery, contin-
uous + 12 V DC
To the car battery, contin-
uous + 12 V DC
Rear Speakers
CJ-DA6920U
Front Speakers
CJ-DA1600U
¡ Exclusively operated with 12 V battery with negative (–) ground.
¡ Connect the power lead (red) very last.
¡ Connect the battery lead (yellow) to the positive (+) terminal of the battery or fuse block terminal (BAT).
¡ Strip about 5 mm {
¡ Connect the power lead (red) very last.
¡ Connect the battery lead (yellow) to the positive (+) terminal of the battery or fuse block terminal (BAT).
¡ Strip about 5 mm {
1
/
4
”} of the lead ends for connection.
¡ Apply insulating tape to bare leads.
¡ Secure loosened leads.
¡ Secure loosened leads.
Before Wiring
*Fuse (15 A) Refer fuse replacement to your near-
est authorized Panasonic Servicenter. Do not try fuse
replacement by yourself.
est authorized Panasonic Servicenter. Do not try fuse
replacement by yourself.
Fuse*
DIN Cord
Motor Antenna Relay Control Lead
(Blue)
(Blue)
Left
Left
Right
Right
Green/black stripe
Violet/black
stripe
stripe
White/black
stripe
stripe
Gray/black
stripe
stripe
Green
Violet
White
Gray
External Amplifier Control Power Lead
(Blue/white stripe)
(Blue/white stripe)
Connect as follows
¡
Use ungrounded speakers only.
Allowable input: 50 W or more
Impedance: 4 – 8
Allowable input: 50 W or more
Impedance: 4 – 8
Ω
¡
Distance between speaker and amplifier: 30 cm {12
”} or more
¡
Do not use a 3-wire type speaker system having a common
earth lead.
earth lead.
Caution
¡ Do not connect more than one speaker to one set of
speaker leads. (except for connecting to a tweeter)
Speaker Connection
–
+
PARKING BRAKE
The parking brake switch position varies with the car
model.
For details on the exact location of the parking brake
switch in your car, contact your dealer.
model.
For details on the exact location of the parking brake
switch in your car, contact your dealer.
q Attach a Clip Connector u to the end
of the parking brake connection lead.
w The Clip Connector u is connected to
the power source side lead of the park-
ing brake.
ing brake.
Connecting the Parking Brake Connection Lead
Hand brake
Foot brake
Parking Brake Lead
(Blue/yellow stripe)
When the parking brake lever is
engaged, the unit is grounded by the
chassis.
(Blue/yellow stripe)
When the parking brake lever is
engaged, the unit is grounded by the
chassis.
Parking brake
switch
switch
Car chassis
Battery
Brake light
Clip Connector u
Parking Brake Lead
(Blue/yellow stripe)
(Blue/yellow stripe)
Power source side lead
Caution
¡ For safety, be sure to ask your nearest professional installer to do this connection.
When connecting this unit to the rear monitor (overhead/headrest):
¡ The parking brake lead and grand lead should be connected to the same terminal.