JVC dr-m10s Manual De Usuario
Masterpage:Right-No-Heading
EN
79
Filename [DR-M10SE_10Editing.fm]
Page 79
February 12, 2004 5:23 pm
A
Make connections.
Connect a camcorder or DV equipment to the DV IN
connector on the unit’s front panel.
connector on the unit’s front panel.
B
Prepare the unit for dubbing.
C Press w e to move H to
, then press
ENTER.
D Press rt repeatedly to select the desired sound track,
then press ENTER.
● Note that this selection is not available when the source
programme is recorded in 16BIT (48 kHz) mode.
E Press REC MODE repeatedly until the desired
recording speed appears. (
C
Prepare the DV equipment for dubbing.
Locate the point from where you want to start dubbing,
then stop or pause playback by pressing the following
buttons on the remote control:
4, 5, 3, 8, 9
then stop or pause playback by pressing the following
buttons on the remote control:
4, 5, 3, 8, 9
● To play back in slow speed (1/10 of the normal speed), press 9
to pause playback, then press 3 or 5.
● To play back frame-by-frame, press 9 to pause playback, then
press 9 repeatedly. Each press of 9 advances a frame.
● To change the playback direction, press 3 or 5.
D
Start dubbing.
Press w e to move the arrow to
, then press
ENTER.
● Playback on the external DV equipment and recording on the
unit should start simultaneously.
● When the playback from the beginning is not possible, the
“DV DUBBING” controller cannot be used. Perform dubbing
without using the “DV DUBBING” controller. (
without using the “DV DUBBING” controller. (
墌
right
column)
● To pause dubbing, press w e to move H to
, then
press ENTER. Both the unit and the external DV equipment
pause dubbing. Pressing 9 on the unit also works the same
way.
pause dubbing. Pressing 9 on the unit also works the same
way.
● To clear the “DV DUBBING” controller from the TV screen,
press ON SCREEN.
E
Stop dubbing.
Press 8 on the remote control.
● Both the unit and the external DV equipment stop dubbing.
NOTES:
● Dubbing copyright guarded programmes is not possible.
● Original DV informations such as the recording date and time
are not recorded.
● The superimposed indication during the operation or dubbing
is not recorded.
● Only DV format image can be dubbed; MPEG2 format image
cannot be dubbed.
Performing dubbing without using the “DV DUBBING”
controller
controller
A Press PR +/– to set the channel to “DV DUBBING”.
B Press REC MODE repeatedly until the desired recording
B Press REC MODE repeatedly until the desired recording
speed appears.
C Start playback on the external DV equipment slightly before
the actual point from where you wish to start dubbing.
D Press and hold 7, then press 4 on the remote control, or
press 7 on the unit.
● Dubbing starts.
E When the dubbing ends, press 8 on the unit, then stop
E When the dubbing ends, press 8 on the unit, then stop
playback on the external DV equipment.
A Load a DVD-RAM/RW/R
disc on the unit.
B Press PR +/– to set the
channel to “DV
DUBBING”.
DUBBING”.
● The “DV DUBBING”
controller appears on the TV
screen.
screen.
● If “
” does not appear on
the “DV DUBBING”
controller, make sure the DV
equipment is connected
correctly.
controller, make sure the DV
equipment is connected
correctly.
AUDIO 1
:
Select this to record the original stereo sound
played back on the connected DV
equipment.
played back on the connected DV
equipment.
AUDIO 2
:
Select this to record the dubbed stereo sound
played back on the connected DV
equipment.
played back on the connected DV
equipment.
MIX
:
Select this to record the sound of both
“AUDIO 1” and “AUDIO 2”.
“AUDIO 1” and “AUDIO 2”.
DR-M10SE_01.book Page 79 Thursday, February 12, 2004 9:08 PM