Yamaha aw1600 Manual De Usuario

AW1600  Owner’s Manual

Appendix

■ Power does not turn on

• Is the AC adaptor connected to an AC outlet of the correct 

voltage?

• Is the POWER switch turned ON?

• If the power still does not turn on, please contact your 

Yamaha dealer.

■ LCD display is dim or dark

• Use the contrast knob located at the lower right of the 

screen to adjust the contrast.

■ Can’t use the [DATA/JOG] dial to control on-

• The [JOG ON] key may be on.

• Some parameters cannot be operated in certain states, 

such as while the recorder is running.

■ No sound, or sound is too faint

• Are speakers or headphones connected correctly?

• Is your amp and other external devices turned on?

• Are you using connection cables with built-in resistors?

• Does the stereo output channel meter move?

• Is the stereo output channel fader raised? Is it turned on?

• The EQ gain may be set to an extremely low value.

• The dynamics processor may be set to an extreme thresh-

old or ratio.

• If you are connecting an electric guitar, is it connected to 

the Hi-Z jack?

• Is the attenuator of the EQ screen or VIEW screen raised?

→ Check the level (meter movement) in the METER page of 

the VIEW screen.

→ If you press the [SEL] key in the MONITOR screen INIT 

page, that channel will be initialized to default values that 
allow sound to be output.

→ If DIGITAL IN is set to other than DISABLE in the UTILITY 

screen D.IN HDD page, and no signal is being input to the 
DIGITAL INPUT jack, a message of “WRONG WORD 
CLOCK” will appear, and sound will not be output.

■ Input sound is not output

• Is the signal from the external device being input?

• The connection cable from the external device may be 

broken.

• Are cables connected to both the MIC/LINE INPUT 8 

XLR/TRS connector and the HI-Z connector?

• Is the [GAIN] knob set to an appropriate level?

• Is the input channel fader raised? Is it turned on?

• The input channel may have been set to DIGITAL IN.

• When recording, is the recording-destination track fader 

(which adjusts the monitor level) raised?

→ If you are recording, the sound of that input channel will not 

be heard during playback.

■ Recorded sound is not output

• Has audio data been recorded on the recorder?

• Is the virtual track set to the track that was recorded?

• A recorded region shorter than 10 msec will not be played 

back.

• Tracks 1–16 will not play back if the AW1600 is in Stereo 

Track, Sound Clip, or Audio CD playback mode.

■ Can’t play back the STEREO track

• Is the stereo track turned on in the MONITOR screen 

ST.TRACK page?

■ Metronome cannot be heard

• The metronome sound is normally sent only to the MONI-

TOR OUT and headphones.

• The metronome will not sound while the recorder is 

stopped.

• In Sound Clip mode, the metronome will sound only dur-

ing recording.

■ Can’t record

• Is there sufficient free space on the internal hard disk?

→ You can check the remaining recordable time by setting the 

counter display to REMAIN in the SONG screen SETUP 
page.

• The song may be protected.

• The stereo track may be in playback mode.

• Is the input signal routed appropriately to the recorder? 

•  Check the recording-source and recording-destination in 

the QUICK NAVIGATE page RECORD screen?

• DIGITAL REC may have been turned OFF in the UTIL-

ITY screen D.IN•HDD page.

• Please read and understand the copyright warning (

before using digital input signals.

■ Can’t record on the STEREO track

• It is not possible to record on the STEREO track while 

recording on other tracks.

Troubleshooting