Yamaha aw1600 Manual De Usuario
Using external effects
15
175
AW1600 Owner’s Manual
Using the A
W1600 with e
xter
nal de
vices
As an alternative to using the internal effects, you can use an external effect processor con-
nected to the STEREO/AUX OUT jacks. As an example, here’s how you can use AUX bus 1 to
apply a mono-in stereo-out reverb to the track channels during mixdown.
nected to the STEREO/AUX OUT jacks. As an example, here’s how you can use AUX bus 1 to
apply a mono-in stereo-out reverb to the track channels during mixdown.
1
Lower the [STEREO] fader to the –
∞
posi-
tion.
2
In the Selected Channel section, repeatedly
press the [PAN/BAL] knob or hold down the
[PAN/BAL] knob and use the CURSOR [
press the [PAN/BAL] knob or hold down the
[PAN/BAL] knob and use the CURSOR [
]/
[
] keys to access the AUX OUT page of
the PAN screen.
In this page you can select one of the following as the
signal that will be output from the STEREO/AUX
OUT jacks.
signal that will be output from the STEREO/AUX
OUT jacks.
• STEREO .....................Stereo bus (default)
• AUX 1/2.......................AUX bus 1/2
3
Move the cursor to the AUX 1/2 button and
press the [ENTER] key.
press the [ENTER] key.
The AUX bus 1 signal will be output from the L chan-
nel of the STEREO/AUX OUT jacks, and the AUX
bus 2 signal will be output from the R channel of the
STEREO/AUX OUT jacks.
nel of the STEREO/AUX OUT jacks, and the AUX
bus 2 signal will be output from the R channel of the
STEREO/AUX OUT jacks.
4
As shown in the following diagram, connect
your external effect processor to the
AW1600.
your external effect processor to the
AW1600.
5
Press the [PAN/BAL] knob twice to access
the AUX page of the PAN screen.
the AUX page of the PAN screen.
1 AUX 1 knobs
Adjust the send level of the signals that are sent from
each channel to AUX bus 1.
each channel to AUX bus 1.
B
PRE/POST (upper line)
Select the location from which the signal is sent from
each channel to AUX bus 1. Move the cursor to the
desired channel and press the [ENTER] key to switch
between the following two settings.
each channel to AUX bus 1. Move the cursor to the
desired channel and press the [ENTER] key to switch
between the following two settings.
• PRE (pre-fader) ......... The signal immediately
before the fader will be sent.
• POST (post-fader)..... The signal immediately after
the fader will be sent.
C
AUX2 knobs
Adjust the send level of the signals that are sent from
each channel to AUX bus 2.
each channel to AUX bus 2.
D
PRE/POST (lower line)
Select the location from which the signal is sent from
each channel to AUX bus 2. Move the cursor and press
the [ENTER] key to switch between PRE and POST.
each channel to AUX bus 2. Move the cursor and press
the [ENTER] key to switch between PRE and POST.
6
Raise the AUX knob 1 of each channel to an
appropriate level, and switch the PRE/POST
setting in the upper line as desired.
appropriate level, and switch the PRE/POST
setting in the upper line as desired.
With the settings so far, the signal from the track chan-
nel will be sent from AUX bus 1 via the STEREO/
AUX OUT jack to the external effect processor.
nel will be sent from AUX bus 1 via the STEREO/
AUX OUT jack to the external effect processor.
7
Use the Quick Navigate section [RECORD]
key to access the MIXDOWN page of the
RECORD screen, and make the settings
shown below.
key to access the MIXDOWN page of the
RECORD screen, and make the settings
shown below.
With these settings, the unprocessed sound of track
channels 1–16 and the effect sound returned to input
channels 3/4 will be sent to the stereo bus and mixed.
You can monitor these signals via the MONITOR
OUT jacks.
channels 1–16 and the effect sound returned to input
channels 3/4 will be sent to the stereo bus and mixed.
You can monitor these signals via the MONITOR
OUT jacks.
Using external effects
AW1600
MONITOR
OUT
OUT
MIC/LINE
INPUT 3/4
STEREO/
AUX OUT (L)
AUX OUT (L)
Effect processor
• If you make the above connection with the [STEREO] fader
raised before performing steps 2 and 3, oscillation may occur.
Please use caution.
Please use caution.
NOTE
34
21