Yamaha aw16g Manual De Usuario
95
Mixdo
wn and bounce oper
ations
9
E
Parameter page/Return channel page
In this area you can edit the various effect parame-
ters. The content and range of the parameters will
depend on the currently-used effect type.
If the effect is internally connected to the mixer sec-
tion via send/return, this area will show the mix
parameters of the return channel, allowing you to
edit them.
ters. The content and range of the parameters will
depend on the currently-used effect type.
If the effect is internally connected to the mixer sec-
tion via send/return, this area will show the mix
parameters of the return channel, allowing you to
edit them.
3
Move the cursor to the effect parameter that
you want to edit, and turn the [DATA/JOG]
dial to edit the value.
you want to edit, and turn the [DATA/JOG]
dial to edit the value.
Depending on the effect type, this area may be used
to show multiple parameter pages. In this case,
repeatedly press the CURSOR [
to show multiple parameter pages. In this case,
repeatedly press the CURSOR [
] key to access
the parameter page that contains the parameter you
want to edit.
For example, the illustration below shows the
parameter pages for the STEREO DELAY effect type.
want to edit.
For example, the illustration below shows the
parameter pages for the STEREO DELAY effect type.
Tip!
Tip!
The parameter pages show the parameters that are spe-
cific to that effect type. However for all effect types, the
lower right of the last parameter page will have a MIX
BAL. parameter which sets the mix balance between the
effect sound and the original sound.
cific to that effect type. However for all effect types, the
lower right of the last parameter page will have a MIX
BAL. parameter which sets the mix balance between the
effect sound and the original sound.
4
To edit the mix parameters of the return
channel, access the last parameter page, and
then press the CURSOR [
channel, access the last parameter page, and
then press the CURSOR [
] key once again.
If the effect is internally connected to the mixer sec-
tion via send/return, you can repeatedly press the
CURSOR [
tion via send/return, you can repeatedly press the
CURSOR [
] key to access the mix parameters of
the return channel. The following pages are the
same for all effect types.
same for all effect types.
1
EFF2SEND
Adjusts the level at which the signal is sent from the
return channel to the other internal effect.
return channel to the other internal effect.
Note
Note
You cannot send the signal from return channel 1 to
insert effect 1 (since this would mean sending the signal
back to the same effect itself). For this reason, the EDIT
page of the EFF1 screen has no send level to effect 1. For
the same reason, the EDIT page of the EFF2 screen has no
send level to effect 2.
insert effect 1 (since this would mean sending the signal
back to the same effect itself). For this reason, the EDIT
page of the EFF1 screen has no send level to effect 1. For
the same reason, the EDIT page of the EFF2 screen has no
send level to effect 2.
B
AUX1SEND
C
AUX2SEND
These adjust the send level of the signal that is sent
from the return channel to AUX buses 1/2.
from the return channel to AUX buses 1/2.
D
EFF2 PRE/POST
Switches the signal that is sent from the return chan-
nel to the other effect bus between pre-fader and
post-fader.
nel to the other effect bus between pre-fader and
post-fader.
E
AUX1 PRE/POST
F
AUX2 PRE/POST
These switch the signals that are sent from the
return channel to AUX buses 1/2 between pre-fader
and post-fader.
return channel to AUX buses 1/2 between pre-fader
and post-fader.
1
EQ HIGH GAIN
B
EQ HIGH FREQ
C
EQ HIGH Q
D
EQ H-MID GAIN
E
EQ H-MID FREQ
F
EQ H-MID Q
These specify the gain, frequency, and Q for the
HIGH and HI-MID bands of the return channel EQ.
The range of each parameter is the same as in the
EDIT page of the EQ screen.
HIGH and HI-MID bands of the return channel EQ.
The range of each parameter is the same as in the
EDIT page of the EQ screen.
MIX BAL. parameter
4
5
6
2
1
3
4
5
6
2
1
3