Edelbrock pro-flo xt 3528 Manual De Usuario
3
Pro-Flo EFI Installation Instructions
©2008 Edelbrock Corporation
Brochure No. 63-3527
Catalog #3527, #3528
Rev. 8/08 - AJ/mc
Rev. 8/08 - AJ/mc
TOOLS AND EQUIPMENT
Use the following checklist for items needed.
❑ Box and open end wrenches
❑ Socket set
❑ Distributor wrench
❑ Pliers (channel locks and hose clamp)
❑ Screwdrivers (regular and Phillips)
❑ Torque wrench
❑ Hammer
❑ Gasket scraper or putty knife
❑ Timing light
❑ Vacuum gauge
❑ Rags
❑ Water bucket
❑ Drill and bits
❑ Hole saw (1 1/4-inch or 1 3/4-inch)
❑ Tubing wrenches
❑ Tubing cutter
❑ Box and open end wrenches
❑ Socket set
❑ Distributor wrench
❑ Pliers (channel locks and hose clamp)
❑ Screwdrivers (regular and Phillips)
❑ Torque wrench
❑ Hammer
❑ Gasket scraper or putty knife
❑ Timing light
❑ Vacuum gauge
❑ Rags
❑ Water bucket
❑ Drill and bits
❑ Hole saw (1 1/4-inch or 1 3/4-inch)
❑ Tubing wrenches
❑ Tubing cutter
P R E L I M I N A RY C H E C K L I S T
1.
CAREFULLY STUDY AND UNDERSTAND ALL INSTRUCTIONS, BEFORE BEGINNING THIS INSTALLATION.
NOTE: This installation can be accomplished using common tools and procedures. However, you should have a basic
knowledge of automotive repair and modification and be familiar with and comfortable working on your vehicle. If you do
not feel comfortable working on your vehicle, it is recommended to have the installation completed by a professional
mechanic.
2.
Examine the Pro-Flo XT system for possible shipping damage. If damaged, contact your dealer immediately.
3.
The 3527 & 3528 kits are designed for use with a standard Small Block Chevy V8 firing order.
4.
Check all threaded manifold holes.
5.
Check all internal manifold passages with a light and wire, making sure they are clean and unobstructed.
6.
Check automatic transmission shift points before removal of your stock manifold and adjust linkage after Edelbrock
manifold installation for same shift points (if needed).
NOTE::
We recommend that you refer to this checklist again after installation to be sure that you have completed all steps.
HARDWARE AND PARTS RECOMMENDED
Use the following checklist for items needed.
❑ Intake gasket; #3527 kits use Edelbrock gaskets #7201; #3528
❑ Intake gasket; #3527 kits use Edelbrock gaskets #7201; #3528
kits use gaskets #7235
❑ Pipe plugs, if needed
❑ 5/16-inch steel tubing (approximate equal length to fuel pickup
❑ 5/16-inch steel tubing (approximate equal length to fuel pickup
line in tank)
❑ Edelbrock Gasgacinch #9300
❑ Loctite 598 OEM High Temperature Silicone Gasket (O
❑ Loctite 598 OEM High Temperature Silicone Gasket (O
2
Sensor
Compatible)
❑ Radiator coolant
❑ Wiring diagram for your vehicle
❑ Teflon tape or liquid Teflon thread sealer
❑ Manifold bolt kit; #3527use #8504; #3528 uses #8516
❑ 195° Thermostat
❑ Resistor type spark plugs (Use correct heat range for your
❑ Wiring diagram for your vehicle
❑ Teflon tape or liquid Teflon thread sealer
❑ Manifold bolt kit; #3527use #8504; #3528 uses #8516
❑ 195° Thermostat
❑ Resistor type spark plugs (Use correct heat range for your
particular application
❑ Set of low-resistance spark plug wires with high EMI suppression
(DO NOT use solid core spark plug wires)
❑ Dynojet wideband commander (Optional, not included)
❑ DB9 Serial cable (Optional, not included)
❑ Late model low profile water neck such as Trans-Dapt #9229 or
❑ DB9 Serial cable (Optional, not included)
❑ Late model low profile water neck such as Trans-Dapt #9229 or
GM #12342034 (chrome)