Behringer FCB1010 Manual De Usuario

MIDI FOOT CONTROLLER FCB1010

If you have selected EXP A or EXP B, you can now enter

the controller number the EXPRESSION PEDAL of your

choice is aimed to send values for. Confirm your selection

with UP/ENTER and enter the lower value (pedal up). Confirm

with UP/ENTER.
Afterwards, enter the upper value (pedal pressed down

completely) and confirm once again with UP/ENTER.

Please keep in mind that the first controller value

always has to be lower than the second controller

value!

You can quit the programming mode at any time by

means of a long press on DOWN. Any confirmed

entries will be stored with the currently selected

PRESET.

How to program the NOTE function is explained in

chapter 2.4.6.

2.4 Detailed PRESET programming

2.4.1 Preset copy function

The preset copy function copies an already programmed preset

to a new preset of your choice. This saves you time, since you

do not have to repeat all adjustments for each newly programmed

preset.
s

Activate CONFIG in the GLOBAL CONFIGURATION (see

chapter 2.2).

Now, press footswitch 5 to activate the copy function.

The VALUE 1 LED lights up. The number in the display and

the footswitch LED start flashing.

Enter the number of the preset you wish to copy and

confirm your selection with UP/ENTER. The VALUE 2 LED

lights up. The number in the display and the footswitch LED

start flashing.

Presets 1 - 10 are stored in bank 0, presets 11 - 20 in

bank 1, and so on.

Enter the target preset and confirm your selection with UP/

ENTER, or cancel with DOWN/ESCAPE.

If you want to copy further presets, please press

footswitch 5 again. Press and hold DOWN/ESCAPE to

quit the GLOBAL CONFIGURATION.

2.4.2 Programming switches

Select the PRESET you wish to edit.

Press DOWN for more than 2.5 sec to enter PRESET

programming mode. The green SWITCH 1/SWITCH 2 LED in

the display starts flashing.

Enable/disable the SWITCHES using footswitches 1 and/or

2 and confirm your selection with UP/ENTER. The

corresponding footswitch and SWITCH LEDs light up.

Exit PRESET programming mode through keeping the DOWN/

ESCAPE key for a few seconds, or press the UP/ENTER

key in order to get to the next page, where you can edit

various MIDI functions for the preset selected at the beginning.

2.4.3 Programming program changes

Select the PRESET you wish to edit.

Keep the DOWN/ESCAPE key pressed longer than 2.5 sec.

to get to the programming mode. The green SWITCH 1/

SWITCH 2 LED in the display starts flashing.

Use the UP/ENTER key to get to the next page. The SELECT

LED in the display is lit.

To program a MIDI function, you have to first activate

it. Individual MIDI functions are activated by keeping

the corresponding keys pressed for a few seconds.

Active MIDI functions are indicated by a permanently

lit footswitch LED.

Select the PROGRAM CHANGE you wish to program for

the selected PRESET by briefly pressing the respective

footswitch (footswitches 1 to 5). The footswitch LED blinks.

Confirm your selection by pressing UP/ENTER. The NUMBER

LED in the display lights up.

Enter the program change command (1 bis 128) via the

footswitch or expression pedal A.

Confirm your selection by pressing UP/ENTER or cancel by

pressing DOWN/ESCAPE. The SELECT LED in the display

lights up.

Select an additional MIDI function you wish to edit or exit

the PRESET programming mode by keeping the DOWN/

ESCAPE key for a few seconds.

2.4.4 Programming CONTROL CHANGES

Select the PRESET you wish to edit.

Keep DOWN pressed for more than 2.5 sec to enter PRESET

programming mode. The green SWITCH 1/SWITCH 2 LED in

the display starts flashing.

Use the UP/ENTER key to get to the next page. The SELECT

LED in the display lights up.

To program a MIDI function, you have to first activate

it. Individual MIDI functions are activated by keeping

the corresponding keys pressed for a few seconds.

Active MIDI functions are indicated by a permanently

lit footswitch LED.

Keep the corresponding footswitch (foot key 6 or 7)

pressed for a few seconds to activate the controller you

wish to edit. The controller is selected by pressing the key

briefly again. The LED blinks.

Confirm your selection by pressing UP/ENTER. The NUMBER

LED in the display lights up.

Enter the desired controller number (0 to 127) by using the

foot keys or the expression pedal A.

Confirm your selection with UP/ENTER. The VALUE 1 LED

in the display lights up.

Use the footswitches 1 through 10/0 or EXPRESSION

PEDAL A to enter the controller value (0 through 127).

To correct your selection, use the DOWN/ESCAPE

key to go one step backward.

Confirm your selection by pressing UP/ENTER. The SELECT

LED in the display lights up.

Select an additional MIDI function you wish to edit or quit

the PRESET programming mode by keeping DOWN/ESCAPE

pressed for a few seconds.

2.4.5 Programming EXPRESSION PEDALS A/B

Select the PRESET you wish to edit.

Keep DOWN pressed for more than 2.5 sec to enter PRESET

programming mode. The green SWITCH 1/SWITCH 2 LED in

the display starts flashing.

Use UP/ENTER to get to the next page. The SELECT LED in

the display begins to light up.

To program a MIDI function, you have to first activate

it. Individual MIDI functions are activated by keeping

the corresponding keys pressed for a few seconds.

Active MIDI functions are indicated by a permanently

lit footswitch LED.

2. PROGRAMMING THE FCB1010