Digidesign 2 Manual De Usuario
Getting Started with Digi 002
46
Digi 002 includes preamps for these sources on
Inputs 1–4, with adjustable gain and available
48-volt phantom power. These inputs have both
XLR and 1/4-inch connectors; the XLR inputs
are specifically for connecting microphones,
and the 1/4-inch inputs are for connecting in-
strument outputs.
Inputs 1–4, with adjustable gain and available
48-volt phantom power. These inputs have both
XLR and 1/4-inch connectors; the XLR inputs
are specifically for connecting microphones,
and the 1/4-inch inputs are for connecting in-
strument outputs.
Line-Level Signals
Keyboards, preamps, and mixers output line-
level audio, which varies with each device be-
tween the –10 dBV and +4 dBu standards.
level audio, which varies with each device be-
tween the –10 dBV and +4 dBu standards.
You can connect line level devices to any of
Digi 002’s Inputs 1–8, as follows:
Digi 002’s Inputs 1–8, as follows:
Inputs 1–4
Inputs 1–4 have both XLR and 1/4-
inch TRS connectors. The XLR connectors are
for connecting microphones only. The 1/4-inch
TRS connectors are for connecting line-level de-
vices or instruments. Since these inputs have ad-
justable gain, they are especially useful for de-
vices that output low-level signals.
for connecting microphones only. The 1/4-inch
TRS connectors are for connecting line-level de-
vices or instruments. Since these inputs have ad-
justable gain, they are especially useful for de-
vices that output low-level signals.
Inputs 5–8
These inputs accept 1/4-inch bal-
anced or unbalanced connections, and can be
switched between –10 dBV and +4 dBu opera-
tion.
switched between –10 dBV and +4 dBu opera-
tion.
To connect an analog audio source to Digi 002, do
the following for your type of input:
the following for your type of input:
Microphones
Plug a microphone directly into
any of the available XLR Microphone Inputs 1–4
on the back panel of the Digi 002.
on the back panel of the Digi 002.
■
Press the Mic/Line/Instrument Selector switch
(located on the top panel of Digi 002) for the
corresponding input so that it is in the “Mic”
position.
corresponding input so that it is in the “Mic”
position.
■
If your microphone requires phantom power,
press the Phantom Power switch (labeled 48V)
for the corresponding input pair.
for the corresponding input pair.
Mic/Line Inputs 1–4 (back panel)
The XLR connectors on Inputs 1–4 are
wired specifically to match the impedance
of microphones. Do not use these XLR con-
nectors for line inputs; use the 1/4-inch con-
nectors instead.
wired specifically to match the impedance
of microphones. Do not use these XLR con-
nectors for line inputs; use the 1/4-inch con-
nectors instead.
MIC
MIC
LINE/ INST
LINE/ INST
LINE/ INST
LINE/ INST
1
2
3
4
MIC
MIC
48V
48V
1/4-inch connectors
Phantom Power
switches
switches
XLR connectors
Line Inputs 5–8 (back panel)
Mic/Line/Instrument Selector switches (top panel)
Although phantom power can be used
safely with most microphones, ribbon mi-
crophones can be damaged by it. You
should always turn off phantom power and
wait at least 30 seconds before connecting
or disconnecting a ribbon microphone.
safely with most microphones, ribbon mi-
crophones can be damaged by it. You
should always turn off phantom power and
wait at least 30 seconds before connecting
or disconnecting a ribbon microphone.
+4 -10
+4 -10
+4 -10
+4 -10
INPUT 5
INPUT 6
INPUT 7
INPUT 8
Operating Level switches
1 GAIN
2 GAIN
3 GAIN
4 GAIN
LINE/ INST
MIC
Mic/Line/Instrument Selector switches