ABC Office 20830 EC Manual De Usuario
CHANGING THE SHRED BAG
When the Shred Bag (10) is full, the shredder will automatically shut down. On the
electronic models an LED indicator will light and an audible alarm will sound.
Changing the Shred Bag is quick and easy if you follow these simple directions.
1. Turn shredder off.
2. Open Door (12) using Door Handle (11) to expose Waste Bin (10) and Shred
2. Open Door (12) using Door Handle (11) to expose Waste Bin (10) and Shred
Bag (9).
3. Pull the Waste Bin and full Shred Bag out of the shredder.
4. Dispose of full Shred Bag.
5. Install new Shred Bag in Waste Bin, draping end of Shred Bag over edge of
4. Dispose of full Shred Bag.
5. Install new Shred Bag in Waste Bin, draping end of Shred Bag over edge of
Waste Bin.
6. Push Waste Bin, with new Shred Bag installed, back into shredder.
7. Close Door (12).
8. Turn on shredder and continue shredding.
7. Close Door (12).
8. Turn on shredder and continue shredding.
CARING FOR YOUR SHREDDER
Clean covers with a clean dry cloth. Do not use water or solvents. Make sure you
disconnect your shredder from its power source before cleaning.
Paper shredders, like all mechanical equipment, need proper maintenance to
ensure efficient operation. Periodic lubrication of the cutting blades is important to
offset the friction generated within the cutting head. Frequency of lubrication will
vary depending on the shred size and the amount of usage. A strip-cut shredder
receiving light use (1 – 2 hours per week) will require lubrication only once or
twice a month, while the same machine used 1 – 2 hours per day will require
lubrication weekly. A cross-cut shredder should be lubricated every ½ hour of
shredding time to maintain maximum capacity and efficiency.
ensure efficient operation. Periodic lubrication of the cutting blades is important to
offset the friction generated within the cutting head. Frequency of lubrication will
vary depending on the shred size and the amount of usage. A strip-cut shredder
receiving light use (1 – 2 hours per week) will require lubrication only once or
twice a month, while the same machine used 1 – 2 hours per day will require
lubrication weekly. A cross-cut shredder should be lubricated every ½ hour of
shredding time to maintain maximum capacity and efficiency.
The procedure for lubricating your shredder is simple, and can be performed by
any operator. The oil is packaged in a squeeze bottle and is applied directly to the
cutting blades through the feed opening (3). Run a fine stream of lubricant from
one side of the feed opening to the other. Run the shredder in REVERSE for a
few seconds to help distribute the lubricant evenly. You can now continue
shredding as usual.
any operator. The oil is packaged in a squeeze bottle and is applied directly to the
cutting blades through the feed opening (3). Run a fine stream of lubricant from
one side of the feed opening to the other. Run the shredder in REVERSE for a
few seconds to help distribute the lubricant evenly. You can now continue
shredding as usual.
DAHLE Shredder Oil is the only lubricant you should use in your paper shredder.
It has been specially formulated so as not to leave any residue that could attract
dust and clog the shredding mechanism. You can order DAHLE Shredder Oil
(item # 740) from your local dealer.
Repairs on your paper shredder should only be performed by qualified
technicians. If you need service, contact your local dealer.
It has been specially formulated so as not to leave any residue that could attract
dust and clog the shredding mechanism. You can order DAHLE Shredder Oil
(item # 740) from your local dealer.
Repairs on your paper shredder should only be performed by qualified
technicians. If you need service, contact your local dealer.
or you can contact
DAHLE North America Customer Service between 8:30 am and 5:00 pm EST at
(800) 995-1379.
(800) 995-1379.
SAFETY INSTRUCTIONS
•
Read the operating instructions carefully before operating your shredder!
•
Do not use in the vicinity of flammable liquids or gases.
•
Do not use in the vicinity of corrosive materials.
•
Do not expose to water or wet conditions.
•
Do not let children operate this, or any other, office equipment.
•
Do not reach into the cutting mechanism during operation - not even from
the top or with objects.
•
Do not operate the shredder for a period of more than 5 minutes in no-load
operation (operation without paper).
•
Keep hair clear of machine.
•
Keep neckties clear of machine.
•
Keep bracelets, or any other jewelry, clear of machine.
•
Power connection must be accessible at all times.
•
Disconnect from power supply before servicing.
•
The safety devices must not be disabled or removed.
•
Please make sure that the shredder gets sufficient ventilation (ventilating
grills must kept free).
BEFORE YOU SHRED
•
Remove Transport Bolts with wrench provided.
•
Record the Model and Serial Number in the space provided inside the front
cover.
•
Be sure the electrical outlet provides the proper power for your shredder
(see rating label on rear of shredder).
•
Install Shred Bag (see: “CHANGING THE SHRED BAG”).
TURNING ON YOUR SHREDDER
20801 S
••••
20801 C
1. ON, OFF and REVERSE are controlled by the black
Rocker Switch (8a) on the top of the shredder.
2. Moving the switch to the “I” (ON) position
activates the shredding mechanism.
3. Moving the switch to the center or “O” (OFF)
position turns the shredder off.
4. The REVERSE position “R” will be discussed
in “CLEARING A PAPER JAM”.
NOTE: SHREDDER WILL NOT OPERATE UNLESS DOOR IS COMPLETELY CLOSED
ALWAYS TURN SHREDDER OFF IF IT WILL BE UNATTENDED FOR LONG PERIODS OF TIME
abcoffice
www.abcoffice.com (800) 658-8788