Philips dvdr1000 Manual De Usuario
10 Hookups (cont’d)
Connecting to a TV Only
TV has Component Video In Jacks
COMPONENT VIDEO
PROG
SCAN
SCAN
EXT 2
Y
Y
P
B
P
B
P
R
Y
L
L
L
R
R
R
P
B
P
R
P
R
EXT 3
EXT 3
EXT 1
EXT 1/2
IN
RC 6
Back of TV
(example only)
4
2
LEFT AUDIO IN
RIGHT AUDIO IN
Pr/Cr
Y
Pb/Cb
LEFT AUDIO IN
RIGHT AUDIO IN
Cr/R-Y
Y
Cb/B-Y
3
Antenna
or Cable TV
Signal
or Cable TV
Signal
1
1
Connect your Antenna or Cable TV signal to the ANTEN-
NA jack on the rear of the DVD Recorder.
NA jack on the rear of the DVD Recorder.
2
Connect the DVD Recorder’s COMPONENT VIDEO OUT
Y P
Y P
B
P
R
jacks (EXT 3) to the corresponding COMPONENT
VIDEO IN jacks on the TV. Use the supplied three-strand com-
ponent video cable, which has ends with red, blue, and green
stripes. Match the cable stripe colors to the jack colors.
ponent video cable, which has ends with red, blue, and green
stripes. Match the cable stripe colors to the jack colors.
3
Connect the DVD Recorder’s red and white AUDIO OUT
(Left and Right) (EXT 3) jacks to the left/right AUDIO IN
jacks on the TV. Use one of the supplied two-strand audio cables,
which has ends with red and white stripes. Match the cable stripe
colors to the jack colors.
(Left and Right) (EXT 3) jacks to the left/right AUDIO IN
jacks on the TV. Use one of the supplied two-strand audio cables,
which has ends with red and white stripes. Match the cable stripe
colors to the jack colors.
4
Connect the supplied power cord to the MAINS (AC
Power) jack on the rear of the DVD Recorder.
Connect the power cords of the DVD Recorder and the TV
to a power outlet.
Power) jack on the rear of the DVD Recorder.
Connect the power cords of the DVD Recorder and the TV
to a power outlet.
5
Press the STAND BY/ON button on the front of the DVD
Recorder to turn on the DVD Recorder. The STAND BY/ON
light will turn green.
Recorder to turn on the DVD Recorder. The STAND BY/ON
light will turn green.
6
Turn on the TV power. Set the TV to the correct
Component Video In channel. See your TV owner’s manual for
details. Or, change channels at the TV until you see the DVD screen
saver or Initial Setup screen on the TV screen. The Initial Setup
screen will appear the first time you turn on the Recorder. Go to page 16
to continue.
Component Video In channel. See your TV owner’s manual for
details. Or, change channels at the TV until you see the DVD screen
saver or Initial Setup screen on the TV screen. The Initial Setup
screen will appear the first time you turn on the Recorder. Go to page 16
to continue.
• If your TV has Progressive Scan,
connect the DVD Recorder’s
PROG SCAN OUT Y P
PROG SCAN OUT Y P
B
P
R
jacks
to the TV’s Progressive Scan In
jacks instead. Progressive Scan
produces a clearer picture by
doubling the number of visible
picture lines per field. This pro-
vides a jitter-free, sharp, quiet
picture. Only use these connec-
tions if your TV has Progressive
Scan. Check your TV manual
for more information.
jacks instead. Progressive Scan
produces a clearer picture by
doubling the number of visible
picture lines per field. This pro-
vides a jitter-free, sharp, quiet
picture. Only use these connec-
tions if your TV has Progressive
Scan. Check your TV manual
for more information.
• On the TV, the component
video in jacks may be labeled
YUV or Pr/Cr Pb/Cb Y and may
be green, blue, and red.
YUV or Pr/Cr Pb/Cb Y and may
be green, blue, and red.
Helpful Hints