Philips VRX342AT Manual De Usuario
REW
PLAY
POWER
VCR PLUS+
/ENTER
SPEED
VCR
TIME SEARCH
TV
MUTE
CABLE
/DSS
VCR/TV
CHANNEL
VOLUME
REC/OTR
STATUS/EXIT
MEMORY
SLOW
PAUSE/STILL
MENU
CLEAR
EJECT
STOP
F.FWD
–
+
1
2
3
4
5
6
7
8
9
0
+100
1
Turn on the TV. Set it to the same channel as the
CH3/CH4 switch on the back of the VCR.
CH3/CH4 switch on the back of the VCR.
2
Press the VCR button, then the POWER button. The VCR
light will appear on the display panel and the language select dis-
play screen shown below will appear. (If the display does not
appear, check your hookups, then follow the steps on page 12 to
program channels and page 19 to select a language.)
light will appear on the display panel and the language select dis-
play screen shown below will appear. (If the display does not
appear, check your hookups, then follow the steps on page 12 to
program channels and page 19 to select a language.)
3
Press the Number 1 button to select English on-screen dis-
plays or the Number 2 button for Spanish on-screen displays.
plays or the Number 2 button for Spanish on-screen displays.
4
Press the MENU button. The channel program display shown
below will appear. The display will disappear after about 60 sec-
onds if you do not press any buttons.
below will appear. The display will disappear after about 60 sec-
onds if you do not press any buttons.
TO SELECT PUSH NO. SHOWN
1 ENGLISH ON
2 ESPAÑOL
2 ESPAÑOL
MAKE SELECTION OR
PUSH MENU TO CONTINUE
CONNECT ANTENNA OR CABLE
TO VCR
TO VCR
THEN . . .
PUSH CH UP KEY
OR . . .
FOR PLAY ONLY – PUSH STOP
Turning on Your VCR 11
5
Press the CHANNEL (Up) button to begin automatic
channel programming. AUTO SET PROCEEDING PLEASE
WAIT will appear on-screen. The VCR will place all of the chan-
nels you receive into its memory, so when you scan through chan-
nels using the CHANNEL (Up/Down) buttons, you’ll only scan
through channels that you receive. When all channels are pro-
grammed, CHANNELS ARE SET will appear on-screen briefly.
Then the TV will go to the lowest channel programmed.
channel programming. AUTO SET PROCEEDING PLEASE
WAIT will appear on-screen. The VCR will place all of the chan-
nels you receive into its memory, so when you scan through chan-
nels using the CHANNEL (Up/Down) buttons, you’ll only scan
through channels that you receive. When all channels are pro-
grammed, CHANNELS ARE SET will appear on-screen briefly.
Then the TV will go to the lowest channel programmed.
• To skip this feature and play a tape
immediately, insert a tape with its
record tab removed. Or, to skip step
3, press the MENU button. All on-
screen displays will be in English. To
skip step 5, press the STOP button.
Channels will not be programmed,
and CHANNELS NOT SET will
appear on-screen.
record tab removed. Or, to skip step
3, press the MENU button. All on-
screen displays will be in English. To
skip step 5, press the STOP button.
Channels will not be programmed,
and CHANNELS NOT SET will
appear on-screen.
• If you try to program channels
when there is no antenna or cable
connected to the VCR, programming
will appear to take place, but even-
tually a NO TV SIGNALS message
will appear on-screen. Connect an
antenna or cable to the VCR’s
ANT(enna) IN Jack and try again.
You may need to follow the steps
on page 12.
connected to the VCR, programming
will appear to take place, but even-
tually a NO TV SIGNALS message
will appear on-screen. Connect an
antenna or cable to the VCR’s
ANT(enna) IN Jack and try again.
You may need to follow the steps
on page 12.
Helpful Hints
2
3
3
4
Before turning on your VCR, make sure there are batteries in the
remote control and the VCR and TV are connected correctly.
remote control and the VCR and TV are connected correctly.
●
Follow the steps on this page only when you plug the VCR
power cord into the wall outlet for the first time.
power cord into the wall outlet for the first time.
●
You may not be able to program channels at step 5 if you are
using a Cable Box.
using a Cable Box.
1
Turn on the TV.
5