Microboards Technology copywriter bluray series Manual De Usuario
BluRay Series MICROBOARDS TECHNOLOGY, LLC
13
Setup Menu
1. At the COPY START? (DISC to DISC) menu, press the NO or ▼ button until the display
shows SETUP? (MODE CHANGE)
SETUP?
SETUP?
(MODE CHANGE)
2. Press the YES button
3. The first setup option is Mode Select, followed by Copy DISC to HD/DISC, Write Speed,
3. The first setup option is Mode Select, followed by Copy DISC to HD/DISC, Write Speed,
ISRC Check, Copy Quantity, Session Mode, Drive Inquiry, Firmware Version and Exit.
4. Pressing the NO or ▼ button will allow you to move from menu to menu.
5. Pressing the YES button will allow you to view or change the configuration of the system.
6. Please follow the flow chart on page 12 to navigate through the Setup menu options.
5. Pressing the YES button will allow you to view or change the configuration of the system.
6. Please follow the flow chart on page 12 to navigate through the Setup menu options.
Here is a description of each setup menu item:
Mode Select
COPY - Duplication from master disc to blank disc, or HDD to blank disc if master data is
registered.
VERIFY - It compares a copied disc with the master disc.
COPY+V - Copying in the COPY+VERIFY mode.
registered.
VERIFY - It compares a copied disc with the master disc.
COPY+V - Copying in the COPY+VERIFY mode.
NOTE ON BD-RE:
If you are using BD-RE media, you should specify WRITE+VERIFY in the
BD-RE setting (see below) rather than COPY+VERIFY. This will result in longer record
times, as the data is being checked while it is being written and re-written if there are
errors, but it makes using COPY+VERIFY unnecessary for BD-RE.
times, as the data is being checked while it is being written and re-written if there are
errors, but it makes using COPY+VERIFY unnecessary for BD-RE.
BD-RE
Default setting is WRITE+VERIFY, which should always be used for BD-RE media. This method
will write each block and then compare the written block to the master; if there are differences,
the block will be re-written. You will not need to run a Copy + Verify on BD-RE media duplicates
if you have this option set to WRITE+VERIFY. When set to WRITE, burn speed to BD-RE will be
faster, but verification cannot be guaranteed.
will write each block and then compare the written block to the master; if there are differences,
the block will be re-written. You will not need to run a Copy + Verify on BD-RE media duplicates
if you have this option set to WRITE+VERIFY. When set to WRITE, burn speed to BD-RE will be
faster, but verification cannot be guaranteed.
Copy HD/DISC
Default setting is OFF. When set to ON, this allows you to copy the master disc to Hard Drive
Partition 1 AND blank discs.
Partition 1 AND blank discs.
BD WR Speed
The burn can be set to 4X or 2X. 4X burn speed will only occur with 4X certified blank media. In
addition, the master must either be on the hard drive or on 4X media for 4X burning.
addition, the master must either be on the hard drive or on 4X media for 4X burning.
DVD WR Speed
Available speeds range from 16x down to 2x.
CD WR Speed
Available speeds range from 40x down to 4x.
Auto Run
Default setting is OFF. When set to ON, this allows the duplicator to start the duplication process
when all recorders are loaded with blank media. If you are copying Disc-to-Disc, the master must
be loaded before duplication will begin.
when all recorders are loaded with blank media. If you are copying Disc-to-Disc, the master must
be loaded before duplication will begin.
Copy Quantity
Set up the number of disc you want to copy.
Use the ▼▲buttons to change the number in the current column up or down. YES will move you
one column to the right, NO will move you 1 column to the left. Press YES when in the right
column to save the number of copies entered. The example above shows that 750 copies have
been entered with the cursor currently in the right column (underlined).
Use the ▼▲buttons to change the number in the current column up or down. YES will move you
one column to the right, NO will move you 1 column to the left. Press YES when in the right
column to save the number of copies entered. The example above shows that 750 copies have
been entered with the cursor currently in the right column (underlined).
Reader Select
Changes which drive is selected as the reader when burning Disc-to-Disc. Any of the drives can
be set as the reader.
be set as the reader.
>>COPY QUANTITY
0750