Mitsubishi diamond pro 91txm Manual De Usuario
7
MEMORY
PRESET
Polarity
BUFFER
TIMING
Fh (KHz)
Fv (Hz)
H
V
1
1600 x 1200 N.I.
93.7
75
+
+
2
1280 x 1024 N.I.
79.9
75
+
+
3
1152 x 870
N.I.
68.7
75
-
-
4
1024 x 768
N.I.
60.0
75
+
+
5
800 x 600
N.I.
46.8
75
+
+
6
640 x 480
N.I.
37.5
75
-
-
Table 1. Memory Buffer Factory Presets
1.2
Internal Preset Memory Capability
To minimize adjustment needs, the factory has preset popular display standards into the monitor,
as shown in Table 1. If any of these display standards are detected, the picture size and center-
ing are automatically adjusted. All of the factory presets may be overwritten by adjusting the user
controls. The monitor is capable of automatically storing up to twelve additional display stan-
dards. The new display information must differ from any of the existing display standards by at
least 1kHz for the horizontal scan frequency or 5Hz for the vertical scan frequency or the sync
signal polarities must be different.
as shown in Table 1. If any of these display standards are detected, the picture size and center-
ing are automatically adjusted. All of the factory presets may be overwritten by adjusting the user
controls. The monitor is capable of automatically storing up to twelve additional display stan-
dards. The new display information must differ from any of the existing display standards by at
least 1kHz for the horizontal scan frequency or 5Hz for the vertical scan frequency or the sync
signal polarities must be different.
1.3
Power Management Function
The monitor has the power management function which reduces the power consumption of the
monitor when not in use. There are two reduced power level modes.
monitor when not in use. There are two reduced power level modes.
Stand-by mode
When the horizontal sync signal is off, the monitor is switched to a stand-by mode. When the
monitor is in stand-by mode, the screen is off and the power indicator will blink for 0.5 second
intervals.
After the horizontal sync signal is restored, picture will be displayed immediately.
When the horizontal sync signal is off, the monitor is switched to a stand-by mode. When the
monitor is in stand-by mode, the screen is off and the power indicator will blink for 0.5 second
intervals.
After the horizontal sync signal is restored, picture will be displayed immediately.
Suspend mode
When the vertical sync signal is off, after about 10 seconds the monitor is switched to a
suspend mode which reduces the monitor power consumption to less than 15W.
When the monitor is in suspend mode, the screen is off and the power indicator will blink for
two second intervals. After the vertical sync signal is restored, picture will be displayed within
a few seconds.
When the vertical sync signal is off, after about 10 seconds the monitor is switched to a
suspend mode which reduces the monitor power consumption to less than 15W.
When the monitor is in suspend mode, the screen is off and the power indicator will blink for
two second intervals. After the vertical sync signal is restored, picture will be displayed within
a few seconds.
Power-off mode
When the horizontal sync signal and vertical sync signal are off, after about 10 seconds the
monitor is switched to a power-off mode, which reduces the monitor power consumption to
less than the power consumed at suspend mode above.
When the monitor is in power-off mode, the screen is off, and the power indicator will blink for
3 seconds of On-time and 1 second Off-time.
After both the sync signals are restored, picture will be displayed within several seconds.
When the horizontal sync signal and vertical sync signal are off, after about 10 seconds the
monitor is switched to a power-off mode, which reduces the monitor power consumption to
less than the power consumed at suspend mode above.
When the monitor is in power-off mode, the screen is off, and the power indicator will blink for
3 seconds of On-time and 1 second Off-time.
After both the sync signals are restored, picture will be displayed within several seconds.