Casio CW-L300 Manual De Usuario
E
60
DISC Mode
Symptom
The printing
operation is
finished
normally,
but nothing
is printed.
operation is
finished
normally,
but nothing
is printed.
Recommended Action
Load a new ink ribbon
cassette (option). (Startup
Guide, page 11)
cassette (option). (Startup
Guide, page 11)
Use a disc that meets the
requirements described in the
bundled “Printing Precautions”
or at the following Internet
URL.
http://world.casio.com/ds/
media/
You can also try adjusting the
print density to make it darker.
(page 55)
requirements described in the
bundled “Printing Precautions”
or at the following Internet
URL.
http://world.casio.com/ds/
media/
You can also try adjusting the
print density to make it darker.
(page 55)
Re-load the ink ribbon
cassette properly.
cassette properly.
Try using a lighter color disc or
a darker color ink ribbon.
a darker color ink ribbon.
Possible Cause
The ink ribbon is used
up.
up.
Any of the following
can interfere with
proper printing.
• A disc printing
can interfere with
proper printing.
• A disc printing
surface that is not
smooth and flat
smooth and flat
• A disc printing
surface that has a
design or lines
printed on it
design or lines
printed on it
• A disc printing
surface that
supports ink jet
printing only
supports ink jet
printing only
The ink ribbon
cassette is not loaded
properly.
cassette is not loaded
properly.
The color of the final
printout is affected by
both the color of the
ink ribbon and the
color of the disc you
are printing on.
printout is affected by
both the color of the
ink ribbon and the
color of the disc you
are printing on.
Printing is
not clear.
Printing is
poor
quality.
Printing is
too light.
not clear.
Printing is
poor
quality.
Printing is
too light.
Symptom
Recommended Action
Possible Cause
The printed
color is
different
from the ink
ribbon
color.
color is
different
from the ink
ribbon
color.
The printing
is not
positioned
correctly on
the disc.
is not
positioned
correctly on
the disc.
The disc
stops part
way
through
printing.
stops part
way
through
printing.
Improper alignment of
the disc when it is
placed in the printer.
the disc when it is
placed in the printer.
The power cord plug
or the AC adaptor is
not plugged in as far
as it will go.
or the AC adaptor is
not plugged in as far
as it will go.
The printer is
malfunctioning.
malfunctioning.
Battery power is low or
the wrong type of
batteries are loaded in
the printer.
the wrong type of
batteries are loaded in
the printer.
Use the positioning guide
when aligning the disc.
(Startup Guide, page 21)
when aligning the disc.
(Startup Guide, page 21)
Correctly connect the power
cord and the AC adaptor.
(Startup Guide, page 7)
cord and the AC adaptor.
(Startup Guide, page 7)
If you cannot easily remove
the disc from between the
print head and roller, do not try
to force it. Insert a thin object
into the print head release
button hole (Startup Guide,
page 4) and press to release
the print head. This should
allow you to remove the disc.
After removing the disc, press
the release lever inside the
cassette case (Startup Guide,
page 4) to its original position
before trying to print again. If
you are still unable to remove
the disc from the printer,
contact your retailer or your
nearest CASIO service center.
the disc from between the
print head and roller, do not try
to force it. Insert a thin object
into the print head release
button hole (Startup Guide,
page 4) and press to release
the print head. This should
allow you to remove the disc.
After removing the disc, press
the release lever inside the
cassette case (Startup Guide,
page 4) to its original position
before trying to print again. If
you are still unable to remove
the disc from the printer,
contact your retailer or your
nearest CASIO service center.
Use the bundled AC adaptor
to power the printer, or replace
the current batteries with a
fresh set of AA-size alkaline
batteries.
to power the printer, or replace
the current batteries with a
fresh set of AA-size alkaline
batteries.