Furuno model 1622 Manual De Usuario
3
1.3 Turning the Radar On/Off
The [POWER] key turns the radar on/off. When
turning on the power, the control panel lights and
the timer displays the time remaining for warm
up of the magnetron (device which transmits
radar pulses), counting down from 1:00 to 0:00.
turning on the power, the control panel lights and
the timer displays the time remaining for warm
up of the magnetron (device which transmits
radar pulses), counting down from 1:00 to 0:00.
Provided that the radar was once in use with
the transmitter tube (magnetron) still warm,
you can turn on the radar into TRANSMIT
status without the one-minute stand-by.
If the power switch has been turned off by
mistake and you want to restart the radar
promptly do the following:
the transmitter tube (magnetron) still warm,
you can turn on the radar into TRANSMIT
status without the one-minute stand-by.
If the power switch has been turned off by
mistake and you want to restart the radar
promptly do the following:
1. Press the [POWER] key not later than five
seconds after power-off.
2. Press the [TX] key. The radar is restored
for full operation.
seconds after power-off.
2. Press the [TX] key. The radar is restored
for full operation.
Quick Start
1.4 Transmitting, Stand-by
After the power is turned on and the magnetron
has warmed up, ST-BY (Stand-By) appears at
the screen center, indicating the radar is ready to
transmit radar pulses.
has warmed up, ST-BY (Stand-By) appears at
the screen center, indicating the radar is ready to
transmit radar pulses.
Press the [TX] key to transmit. Echoes appear in
four levels of digitized video according to echo
strength. Note that when a target is beneath a
marker (VRM, EBL, heading marker, range ring)
the part of the marker where the target lies is
displayed in reverse video.
four levels of digitized video according to echo
strength. Note that when a target is beneath a
marker (VRM, EBL, heading marker, range ring)
the part of the marker where the target lies is
displayed in reverse video.
Note: If you press the [TX] key before the
indication ST-BY appears, the buzzer sounds
and the radar does not transmit pulses.
indication ST-BY appears, the buzzer sounds
and the radar does not transmit pulses.
When you won’t be using the radar for an
extended period, but you want to keep it in a
state of readiness, press the [TX] key to set the
radar in stand-by.
extended period, but you want to keep it in a
state of readiness, press the [TX] key to set the
radar in stand-by.
1.5 LCD Tone and Brilliance
1. Press the [TONE] key. The dialogue shown
in Figure 1-3 appears.
TONE: 12
LOW
HIGH
BRILL: 3
LOW
▼
▲
HIGH
▲
▲
Figure 1-3 Dialogue for adjustment of
LCD tone and brilliance
2. Press
or
or the [TONE] key to adjust
tone;
▲ or ▼ to adjust brilliance.
The dialogue for adjustment of tone and
brilliance is automatically erased when there is
no TrackDisk operation for about 10 seconds. To
erase it more quickly, press the [TONE] key after
making the adjustment.
brilliance is automatically erased when there is
no TrackDisk operation for about 10 seconds. To
erase it more quickly, press the [TONE] key after
making the adjustment.
1.6 Selecting the Range
The range selected automatically determines the
range ring interval, the number of range rings
and pulse repetition rate.
range ring interval, the number of range rings
and pulse repetition rate.
Press the [+] or [-] key to select a range. The
range and range ring interval appear at the top
left corner on the screen.
range and range ring interval appear at the top
left corner on the screen.
045.0
°
3.35
NM
Range
Range ring
interval
interval
6.0
NM
2.0
Figure 1-4 Location of range and range
ring interval indications