bello-1 pvs4215 installation Manual De Usuario

FOR YOUR SAFETY, PLEASE FOLLOW THESE PRECAUTIONS:

! ALWAYS REMOVE THE TV AND OTHER EQUIPMENT FROM THE FURNITURE PRIOR TO MOVING THE ASSEMBLED UNIT.

! BE CAREFUL WHEN MOVING THE ASSEMBLED FURNITURE AFTER THE GLASS SHELVES HAVE BEEN INSTALLED,

AND/OR WHEN THERE IS EQUIPMENT LOCATED ON THE FURNITURE AS THIS MAY CAUSE THE SHELVES TO
BECOME UNSECURED AND FALL.

! WHEN IN USE, THIS FURNITURE MUST BE PLACED ON A FLAT, SOLID AND LEVEL SURFACE.

! DO NOT LEAN ON THE TV WHEN IT IS ON THE TV STAND.

! DO NOT CLIMB OR STEP ON THE STAND.

! DO NOT BANG OR PLACE YOUR OWN WEIGHT ON THE GLASS SHELF.

! DO NOT PLACE ITEMS ON THE SHELVES WHICH EXCEED THE MAXIMUM WEIGHT LIMITS OF 200 LBS. FOR TOP SHELF

AND 50 LBS. FOR MIDDLE AND LOWER SHELVES

Parts List

Hex Nut

Cam Locks

Smaller Hex

Head Screw

Larger Hex

Head Screw

Cam Lock Pin

Middle Shelf

Support Post

Bottom Shelf

Support L-Bracket

Plastic Cap

Long Threaded

Connection Rod

Small Threaded

Connection Rod

PART #

QTY.

PART DESCRIPTION

TOOLS

PART #

QTY.

PART DESCRIPTION

CMS

Panel

Top Glass Shelf

Middle Glass

Shelf

Bottom Glass

Shelf

Front Foot

Cylinders

Rear Foot

Cylinders

Middle Shelf Leg

Cylinders

Lower Shelf Leg

Cylinders

Allen

Wrench

Philips

Screwdriver

Assembly Instructions

NOTE: TWO PEOPLE ARE RECOMMENDED TO ASSEMBLE THIS TABLE.

A. PLACE the Top (least deep) Glass Shelf (1) upside down, on a soft

flat surface, with the silver discs facing upward. SCREW the two

Cam Lock Pins (12) into the small silver discs located at the rear of

the Shelf and tighten as shown in Fig. 1. DO NOT OVERTIGHTEN.

B. INSERT the CMS

(Cable Management System) Panel (2) onto the ends

of the two Cam Lock Pins (12) with the Cam Locks (18) facing the rear

of the table. TIGHTEN the two Cam Locks using the Philips Screwdriver

as shown in Fig. 1A. INSERT one end of the two Long Threaded

Connection Rods (10) into each of the larger silver discs as shown in

Fig. 1, and tighten using the supplied Wrench. DO NOT OVERTIGHTEN.

C. SLIDE the two metal Middle Shelf Leg Cylinders (5) over the

exposed ends of the Long Threaded Connection Rods (10). SCREW

the Middle Shelf Support Post (14) into the pre-drilled hole located

in the front center of the CMS

Panel (2) as shown in Fig. 2B.

CAREFULLY SLIDE the Middle Glass Shelf (3) (the one without the

silver discs) onto the Threaded Rods so that it is sitting on the end

of the Cylinder, and PLACE the rear edge of the Middle Glass Shelf

under the Shelf Support Post.

D. SLIDE the two metal Lower Shelf Leg Cylinders (6) over the

Threaded Rods (10) so that it is resting on the Middle Glass Shelf

(3) as shown in Fig. 2A. SCREW the two Bottom Shelf Support

L-Brackets (15) into the lower rear inside of the CMS

Panel (2)

using the Larger Hex Head Screws (9) as shown in Fig. 3B.

E. CAREFULLY place the front of the Bottom Glass Shelf (4), with the

large silver discs positioned away from the CMS

Panel (2), onto the

exposed end of the Threaded Rods (10), and POSITION the silver discs

at the rear of the Bottom Shelf beneath the two Bottom Shelf Support

L-Brackets (15) as shown in Fig. 3. SECURE the small silver discs to

the Shelf Support L-Brackets using the Smaller Hex Head Screws (17)

as shown in Fig. 3B. NOTE: The table will be upside down at this

point, so the bottom glass shelf will now be at the top of the table.

F. PLACE the metal Rear Foot (taller) Cylinder (7) over the exposed ends

of the Threaded Rods (10). PLACE a Hex Nut (13) over the exposed

ends of the Threaded Rods and TIGHTEN securely. PLACE a Plastic Cap

(16) over the end of each Threaded Rod as shown in Fig. 3A.

G. SCREW one Small Threaded Connection Rod (11) into each of the

large silver discs in the front of the Bottom Glass Shelf (4). PLACE

the metal Front Foot (shorter) Cylinder (8) over the exposed ends

of the Small Threaded Connection Rods as shown in Fig. 3C.

PLACE a Hex Nut (13) over the exposed ends of the Threaded Rods

and TIGHTEN securely. PLACE a Plastic Cap (16) over the end of

each Threaded Rod.

H. CAREFULLY turn the assembled table over so that it is no longer

upside down. CAREFULLY position the table in the location that it

will be used.

IMPORTANT: ALWAYS PLACE THE HEAVIEST EQUIPMENT ON THE

BOTTOM SHELF. DO NOT PLACE ITEMS ON THE SHELVES WHICH

EXCEED THE MAXIMUM WEIGHT LIMITS OF 200 LBS. FOR TOP

SHELF AND 50 LBS. FOR MIDDLE AND LOWER SHELVES.

Fig. 1

Fig. 2

Fig. 3

Fig. 3A

Fig. 3B

Fig. 2A

Fig. 1A

Fig. 2B

Fig. 3C