Panasonic MCCG881C Guía De Operación

24

C-1 

 Pull out the mains lead and put the plug into the socket 

outlet.

C-2 

 Gently press the center of the switch pedal to turn ON 

the appliance. Press the pedal again to turn it OFF.

C-3 

 Power control

The suction power can be adjusted depending on the 

type of fl ooring. 

The symbols on the controls indicate the type of use the 

settings are suitable for.

 

 Turn the rotary selector to the desired suction power 

setting.

C-4 

 Switching between carpet and fl ooring

Flooring: Press lever A 

Carpet: Press lever B

C-5 

  The curved wand of the hose is attached with a manual 

suction regulator, which allows you to reduce the suction 

level easily.

C-6 

 The dusting brush can be set between the telescopic 

wand and the fl oor nozzle if you want. Remove the fl oor 

nozzle by pressing the release pedal and you can use 

the dusting brush easily anytime.

C-7  

 After you fi nish vacuuming, remove the plug from the 

socket outlet and press the cord rewind pedal.

When rewinding the mains lead, press the cord rewind 

pedal by holding the plug so that it does not become 

damaged.

C-8 

 Storage position

Slide the wand holder straight into the wand supporter 

on the under side of the main body.

C-9 

 Park position

For short breaks during vacuuming, slide the wand 

holder straight into the wand supporter on the rear side 

of the main body. 

NOTE:  When you use park position, we suggest that 

you switch the appliance off.

Floor nozzle

Connection pipe

Hose

Suction regulator

Curved wand

Telescopic wand

Dusting brush

Crevice nozzle   

Upholstery nozzle

Hose inlet

Dust indicator

Dust cover

ON/OFF Switch pedal

Cord rewind pedal

Variable power control

Exhaust cover   

Plug

Paper dust bag

Basket

B-1 

 Insert the connection pipe into the hose inlet until it 

locks. 

When removing the hose, push the two connection 

buttons down while pulling out the connection pipe.

NOTE: Do not bend, pull and step on the hose or put 

anything heavy on it.

B-2 

  Insert the curved wand into the upper end of the 

telescopic wand. 

Twist the telescopic wand so that the round hole will fi t 

into the tab on the curved wand. (When removing the 

curved wand, push the tab down while pulling out the 

telescopic wand.) 

Attach the fl oor nozzle to the other end.(Removal as per 

reverse procedure)

B-3 

  Hold the grip and the extension adjuster and extend the 

telescopic wand to the required length.

•  This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or   

lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a 

person responsible for their safety.

• Children should be supervised to ensure that they do not play with the appliance.

• Do not use the appliance if the mains lead or plug is damaged or faulty.

•  If the mains lead is damaged, it must be replaced by the manufacturer, its service agent or similarly qualifi ed persons in order to 

avoid a hazard.

• Unplug from the socket outlet when not in use and before cleaning the appliance or undertaking maintenance operations. 

• Turn off the appliance before removing the plug. Do not pull on the mains lead, always pull on the plug body itself.

• Hold the plug, when rewinding the mains lead.

• Do not handle plug or vacuum cleaner with wet hands.

• Do not use wet fi lters after wash, make sure they are completely dry to avoid damaging the cleaner.

• Do not vacuum fl ammable or combustible substances, neither use in areas where they may be present.

• Do not vacuum hot ash, embers or large and sharp objects.

• Do not vacuum water or other liquids. 

• Keep the vacuum cleaner away from heat sources such as radiators, fi res, direct sunlight, etc.

•  This vacuum cleaner is fi tted with a thermal cut-out device which automatically turns off the cleaner to prevent overheating of the 

motor. When this happens, disconnect the cleaner from the socket outlet and check the dust compartment and fi lters as they may 

be full or clogged with fi ne dust. Check for any other obstructions in the hose or tube.  After removing the obstruction, leave the 

cleaner to cool down until the thermal cut-out resets after approximately 60 minutes.