Panasonic PTD7600E Guía De Operación
35
ENGLISH
Powering up the projector
Connect the supplied power cable.
(220 V–240 V~, 50 Hz/60 Hz)
(220 V–240 V~, 50 Hz/60 Hz)
Press the “I” marked side of the MAIN
POWER switch to turn on the power.
POWER switch to turn on the power.
The power indicator lamp on the projector will flash
in red. After a short period, the indicator will
illuminate and the projector will enter standby
mode.
in red. After a short period, the indicator will
illuminate and the projector will enter standby
mode.
Press the “l” button. [on the main unit
or the remote control]
or the remote control]
The power indicator lamp illuminates in green and
soon the image is projected on the screen.
soon the image is projected on the screen.
Making adjustment and
selection
selection
Roughly adjust the focus of the lens.
(Refer to page 37.)
(Refer to page 37.)
Press the LENS button on the main unit or the
remote control unit to display a focus adjustment
screen. Pressing
remote control unit to display a focus adjustment
screen. Pressing
buttons to adjust
the image into focus.
Select and set the projection scheme.
(Refer to page 68.)
(Refer to page 68.)
Select the input signal by pressing the
input selector button to toggle through
RGB1, RGB2, VIDEO, S-VIDEO and
AUX. [on the main unit or the remote
control]
input selector button to toggle through
RGB1, RGB2, VIDEO, S-VIDEO and
AUX. [on the main unit or the remote
control]
Adjust the tilt of the main unit in front
and rear or right and left.
(Refer to page 18.)
and rear or right and left.
(Refer to page 18.)
Press the LENS button two or three
times to adjust the lens shift. (Refer to
page 37.)
times to adjust the lens shift. (Refer to
page 37.)
• If the projector is powered up at about 0˚C, a warm-
up period of approximately five minutes may be
necessary to start projection.
The temperature monitor (TEMP) lamp flashes during
the warm-up period.
When the warm-up is completed, the temperature
monitor (TEMP) lamp turns off and the image is
projected on the screen.
necessary to start projection.
The temperature monitor (TEMP) lamp flashes during
the warm-up period.
When the warm-up is completed, the temperature
monitor (TEMP) lamp turns off and the image is
projected on the screen.
• If the surrounding temperature is very low and the
warm-up period exceeds five minutes, the control
determines it as an abnormal condition and turns off
the power automatically. If this happens, raise the
surrounding temperature to 0°C or higher and then
turn the main power “on” and turn the power “on” (|).
determines it as an abnormal condition and turns off
the power automatically. If this happens, raise the
surrounding temperature to 0°C or higher and then
turn the main power “on” and turn the power “on” (|).
• The AUX button is disabled when an optional input
module is not connected.
• When the lamp illuminates, the lamp power mode is
set to “HIGH” for about two minutes to bring the lamp
into a stable condition in a short time.
into a stable condition in a short time.
Note
AUTO
SETUP
RGB 1
VIDEO
MENU
ENTER
LENS
S-VIDEO
SHUTTER
RGB 2
AUX
POWER
ON
OFF
RGB
1
RGB
2
AUX
MENU
STD
LENS
OSD
1
4
7
2
5
8
3
6
9
0
NEXT
USER
LIGHT
ID ALL
ASPECT
ID SET
Projector
Computer
Numetric
BRIGHT
CONTRAST
ON SCREEN
SYSTEM
SEL
FUNC
1
D.ZOOM
ENTER
PAGE
UP
PAGE
DOWN
VIDEO
SHUT
S-
VIDEO
FREEZE
SHUTTER
AUTO
SETUP
LASER ON/OFF
Press the AUTO SETUP button if the
input signal is RGB signal. [on the
main unit or the remote control]
input signal is RGB signal. [on the
main unit or the remote control]
Fit the image size to the screen size.
(Refer to page 37.)
(Refer to page 37.)
Press the LENS button twice and adjust the zoom
of the lens on the lens zoom adjustment menu.
of the lens on the lens zoom adjustment menu.
Press the LENS button and adjust the
focus of the lens on the lens focus
adjustment menu.
focus of the lens on the lens focus
adjustment menu.
Display the zoom adjustment menu
again and adjust the zoom of the lens
to fit the image size to the screen size.
(Refer to page 37.)
again and adjust the zoom of the lens
to fit the image size to the screen size.
(Refer to page 37.)
Projection