Nolan Systems Inc. NSRX3C2XXX Manual De Usuario

other function. 

 

Either device has been switched off. 

 
POWERING YOUR RX 

To turn on the Rx - Press and hold the Talk button for about 
3 seconds, the LED will flash once. The Rx is now turned on 
and in pairing mode; the LED will blink in fast speed in pairing 
mode. 
To turn off the Rx - Press and hold the Talk button for about 
5 seconds, the Rx is turned off after the LED stay on. Then 
release the Talk button. 

To HSF profile - Choose connect to the HSF profile of 
“Rx_HSF” on your mobile phone, refer to the user manual for 
this feature. For AV profile not supported mobile phone, 
connect “Rx_HSF” will connect to HSF profile. 

To AV profile - Choose connect to the AV profile of 
“Rx_HSF” on your Bluetooth Audio transmitter, after 
connected, the Rx will receive and play the audio from the 
Bluetooth audio device. For some embedded Bluetooth audio 
transmitter, the AV connection will be setup automatically by 
transmitter. 
 
MAKING CALLS 

You can make calls from your mobile phone or directly from 
Rx using voice dialing (if it’s supported by the phone) 

To make calls from your mobile phone - Dial the call from 
your mobile phone and the call is automatically connected to 
your Rx.   

To make calls using voice dialing (if supported by your 
mobile phone) – With phone is in standby mode, short press 
the Talk button; Speak the name of the person you wish to 
call. The call is automatically connected to your mobile 
phone. 

You must configure your mobile phone to answer calls 
directly on your Bluetooth headset. Refer to the mobile phone 
user guide for instructions for initiating this feature. 
When your mobile phone rings, press the Talk button on your 
headset. The call is automatically connected to your headset.   
Please note you can also Reject calls by depressing the talk 
button for about 3 seconds. (Not all phones support this 
feature) 

When you have finished your call, press the Talk button on 
your headset. The call will be disconnected. 

You can transfer calls connected to your headset back to your 

mobile phone. (Not all phones support this feature) 
To transfer calls from your headset to the phone press the Talk 
button for more than 3 seconds until you hear the tone. 

Press the talk button when Headset is not on a call, a voice prompt 
will be heard. This is also a phone dependent feature 

Fit earphone to Rx, Plug your earphone into the Rx’s 3.5 
mm audio jack 

Play music while keeping mobile device active 
While you are listening the music, the Rx will indicate an 
incoming call by a ring sound if you have incoming call. To 
receive calls please refer to receive calls parts. 
With you are listening to the music, you make a phone call, 
the phone voice will connect to the Rx automatically. 

Note: Generally, the music may resume in 5 seconds after 
the call has been terminated. However, depending on the 
software of the target device, the delaying time may vary and 
may not resume back to the music.   

For some AV profile supported phone, you just need to pair 
the Rx with the phone one time, and phone will judge which 
profile should be used for call and audio transfer, please refer 
to the user guide for the phone. 

Fast speed blink - 10 times per second, the Rx is trying to 
pair/connect to another device. 
Middle speed blink - Once per second, the Rx is connected with 
another device. 
Middle long blink - Long lighted once per second, the Rx is 
receiving music or phone call from other device. 
Low speed blink - Once per 5 seconds, the Rx is in idle mode, it’s 
waiting for other device to connect to it. 

Please note that you should also be familiar with the operation of 
your mobile phone and how to connect to Bluetooth devices. 
Please read your mobile phone user guide carefully. Please note 
that the Bluetooth headset will only work with Bluetooth mobile 
phones. For operation with a PC or laptop device please note that 
these devices should also be Bluetooth enabled with appropriate 
third party software in order to enable correct operation. 
 
 

When Talk button is 
pressed, no LED 
indicator 

•  Check battery power. 
•  Consult authorized dealer 

Rx powers on with 
blue LED flashing but 
no connection to 
mobile phone 

•  Check unit is paired to phone. 

Check settings in phone. 
Headset default name is 
RX_HSF 

•  Check phone is switched on 
•  Check hands-free settings for 

phone 

•  Ensure Rx & phone are within 

range 

Rx powers on with 
blue LED flashing but 
no connection to 
Bluetooth audio 
transmitter 

•  Check the unit is paired to the 

device. 

•  Check the Bluetooth audio 

transmitter is switch on. 

•  Ensure the Rx & Bluetooth 

Audio devices are within 
range. 

 

For other Nolan Bluetooth products or support, please view our 
website – 

www.nolan-sys.com

 or email info@nolan-sys.com or 

contact your local representative. 
 
DISCLAIMER 

Whilst every effort has been made to ensure that the 
information in this manual is accurate and complete, no liability 
will be accepted for any errors and/or omissions made. The 
manufacturer reserves the right to make changes and 
improvements to the specifications and features of the 
hardware and firmware of the products described in this 
document without prior notice. Reproduction, transfer, 
distribution or storage of part or all of the contents in this 
document in any form is prohibited without prior permission of 
the manufacturer. All trademarks acknowledged.