Wistron Corporation TP7500WE Manual De Usuario
<Rear view>
<Top side view> <Left side view> <Right side view>
<Bottom side view>
Installing Main battery
1. Insert the main battery into battery tray
in the direction opposite to mark.
2. Slide Battery Latch/Lock to locked position. ( )
Replacing Main battery
1. Save any active data and power off this device.
2. Slide Battery Latch/Lock to unlocked position. ( )
If this device not power off correctly, beep buzzer and LED light on Red. Please wait until buzzer
2. Slide Battery Latch/Lock to unlocked position. ( )
If this device not power off correctly, beep buzzer and LED light on Red. Please wait until buzzer
does not beep and LED light off.
3. While keep to hold Battery spring-loaded latch to top direction, slide the battery pack out of the
battery tray by pulling it
in the direction opposite to mark.
4. Make sure Battery Latch Lock to unlock position, and slide the battery pack into the battery tray and
firmly push it in until it is firmly set, and then slide Battery Latch/Lock to locked position.
Charging Main battery
1. Power off this device.
2. Plug the AC adapter into the DC input jack on the right side of this device.
2. Insert the AC adapter’s plug into a wall outlet.
3. LED on the front and right side of this device lights on Green if charging starts correctly.
3. LED on the front and right side of this device lights on Green if charging starts correctly.
LED light on Green: In charging
LED light off: Charging complete
LED light off: Charging complete
4. It takes about 2.5 hours until charging completes.
Operation
Power on this device
Keep to press power key until LED lights on Green and Windows boot up.
Show log-on window, please input password to “1” (Default setting) to show Setup wizard.
Follow the instruction to set up. (Product name / Date / Time / Calibration)
Calibrate Touch screen
Press [F2] key to pop-up “System Dialog” window. Tap “Calibration” button in Dialog box and follow the
instructions on screen to tap 9 points. To cancel calibration, press [ESC] key.
And press [F2] key again to hide “System Dialog” window.
Adjusting the speaker volume
Press [F2] key to pop-up “System Dialog” window. Tap [>] or [<] button in Dialog box to adjust volume.
And press [F2] key again to hide “System Dialog” window.
Using the Screen keyboard
Press [F1] key to pop-up “Screen keyboard”
Keep to press power key until LED lights on Green and Windows boot up.
Show log-on window, please input password to “1” (Default setting) to show Setup wizard.
Follow the instruction to set up. (Product name / Date / Time / Calibration)
Calibrate Touch screen
Press [F2] key to pop-up “System Dialog” window. Tap “Calibration” button in Dialog box and follow the
instructions on screen to tap 9 points. To cancel calibration, press [ESC] key.
And press [F2] key again to hide “System Dialog” window.
Adjusting the speaker volume
Press [F2] key to pop-up “System Dialog” window. Tap [>] or [<] button in Dialog box to adjust volume.
And press [F2] key again to hide “System Dialog” window.
Using the Screen keyboard
Press [F1] key to pop-up “Screen keyboard”
.
And press [F1] key again to hide “Screen keyboard”.
Checking Battery status
Press [F2] key to pop-up “System Dialog” window. It shows the status of Battery.
Storage of the Battery
Please do not store battery pack over a year without charging it because it may cause deterioration of
its quality. Charge this battery pack at least once a year for about an hour if stored without use.
Please do not store battery pack over a year without charging it because it may cause deterioration of
its quality. Charge this battery pack at least once a year for about an hour if stored without use.
Battery pack should be stored at a room temperature.
Pen Holder
Battery
Latch/Lock
Latch/Lock
Main battery
Battery
Spring-loaded
latch
Spring-loaded
latch
Reset button
SD card slot
Serial Port
(Serial / USB)
Pen Holder
Cradle Interface
USB Port
Headphone Jack
SD card slot
DC jack
Battery Pack